strange wireless problem in 3.4

[alaing]

Hi all,

I have been using 3.3 HD install on my Dell Latitude LS notebook wiith wireless card with Prism chipset with no problems. Trying 3.4 (CEBIT and downloaded version) it works fine when i boot from CD, but after HD isntall the wireless card does not work anymore. As you can see from dmesg output it is first recognized, but then gets lost .. Any ideas ?

Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Found IRQ 10 for device 00:0a.0
PCI: Sharing IRQ 10 with 00:0d.0
PCI: Sharing IRQ 10 with 01:00.0
Yenta ISA IRQ mask 0x0ab0, PCI irq 10
Socket status: 30000010
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0820-0x08ff: clean.
cs: IO port probe 0x0800-0x080f: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x170-0x177 0x370-0x37f 0x398-0x39f 0x3f8-0x3ff 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
orinoco.c 0.13e (David Gibson <hermes@gibson.dropbear.id.au> and others)
orinoco_cs.c 0.13e (David Gibson <hermes@gibson.dropbear.id.au> and others)
eth0: Station identity 001f:0005:0001:0003
eth0: Looks like an Intersil firmware version 1.3.5
eth0: Ad-hoc demo mode supported
eth0: IEEE standard IBSS ad-hoc mode supported
eth0: WEP supported, 104-bit key
eth0: MAC address 00:06:AB:00:4C:6D
eth0: Station name "Prism I"
eth0: ready
eth0: index 0x01: Vcc 5.0, irq 5, io 0x0100-0x013f
eth0: New link status: Connected (0001)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 19:48:59 Apr 17 2004
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 10 for device 00:07.2
usb-uhci.c: USB UHCI at I/O 0xfce0, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usbdevfs: remount parameter error
eth0: New link status: Connected (0001)
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
PCI: Found IRQ 10 for device 00:0d.0
PCI: Sharing IRQ 10 with 00:0a.0
PCI: Sharing IRQ 10 with 01:00.0
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
00:0d.0: 3Com PCI 3c905C Tornado at 0xfc00. Vers LK1.1.18-ac
00:b0:d0:4d:f7:81, IRQ 10
product code 0000 rev 00.14 date 10-11-97
Internal config register is 1800000, transceivers 0xa.
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 7809.
Enabling bus-master transmits and whole-frame receives.
00:0d.0: scatter/gather enabled. h/w checksums enabled
NeoMagic 256AV/256ZX audio driver, version 1.1p
PCI: Found IRQ 10 for device 01:00.1
NM256: Found card signature in video RAM: 0x27ec00
NM256: Mapping port 1 from 0x266c00 - 0x27ec00
Initialized NeoMagic 256AV audio in PCI native mode
Initialized AC97 mixer
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 94M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xf8000000
eth0: Error -110 setting multicast list.
eth0: New link status: Connected (0001)
orinoco_lock() called with hw_unavailable (dev=c363b800)
cs: unable to map card memory!
cs: unable to map card memory!
cs: unable to map card memory!
cs: unable to map card memory!
cs: unable to map card memory!
cs: unable to map card memory!
cs: unable to map card memory!
cs: unable to map card memory!
cs: unable to map card memory!
cs: unable to map card memory!
cs: unable to map card memory!
cs: unable to map card memory!
cs: unable to map card memory!

See you on the bitstream, Alain