bstumm
12-07-2005, 06:49 PM
I have a Solid Year ACK-540U USB Combo Keyboard and Touchpad, basically the guts of a laptop with a USB connection for a desktop PC. The keyboard works fine regardless of the bios legacy setting but the touchpad portion refuses to work no matter what PC its connected to or distro/kernel used with it. In win98SE and XP it works with no special drivers. Its a USBHID device. Would appreciate any ideas for getting this device working (even a work-around) or advice on how to go about further debug or troubleshooting. This appears to be at kernel level not an issue with the X config and driver.
When I cat /dev/input/mice or /dev/input/event1, etc and move finger on touchpad I get no "jibberish" as expected.
Here is some more info...
From /proc/bus/input/devices
I: Bus=0003 Vendor=060b Product=0541 Version=0101
N: Name="USB Keyboard"
P: Phys=usb-0000:00:10.0-1/input0
H: Handlers=kbd event0
B: EV=120003
B: KEY=10000 7 ff800000 7ff febeffdf f3cfffff ffffffff fffffffe
B: LED=7
I: Bus=0003 Vendor=060b Product=0541 Version=0101
N: Name="USB Keyboard"
P: Phys=usb-0000:00:10.0-1/input1
H: Handlers=kbd mouse0 event1 ts0
B: EV=7
B: KEY=1fffff 0 0 3878 d801d101 1e0000 0 0 0
B: REL=103
root@localhost:~# lspci -v
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8623 [Apollo CLE266]
Subsystem: VIA Technologies, Inc.: Unknown device 0000
Flags: bus master, 66MHz, medium devsel, latency 8
Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Capabilities: [c0] Power Management version 2
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: dde00000-dfefffff
Prefetchable memory behind bridge: d5d00000-ddcfffff
Capabilities: [80] Power Management version 2
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at e400 [size=32]
Capabilities: [80] Power Management version 2
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Flags: bus master, medium devsel, latency 32, IRQ 9
I/O ports at e800 [size=32]
Capabilities: [80] Power Management version 2
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Flags: bus master, medium devsel, latency 32, IRQ 12
I/O ports at ec00 [size=32]
Capabilities: [80] Power Management version 2
0000:00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at dfffff00 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: VIA Technologies, Inc.: Unknown device 0000
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management version 2
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
Flags: bus master, medium devsel, latency 32, IRQ 14
I/O ports at fc00 [size=16]
Capabilities: [c0] Power Management version 2
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
Subsystem: Elitegroup Computer Systems: Unknown device a101
Flags: medium devsel, IRQ 12
I/O ports at e000 [size=256]
Capabilities: [c0] Power Management version 2
0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet Controller on VT8235
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at dc00 [size=256]
Memory at dffffe00 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
0000:01:00.0 VGA compatible controller: VIA Technologies, Inc. VT8623 [Apollo CLE266] integrated CastleRock graphics (rev 03) (prog-if 00 [VGA])
Subsystem: VIA Technologies, Inc. VT8623 [Apollo CLE266] integrated CastleRock graphics
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 11
Memory at d8000000 (32-bit, prefetchable) [size=64M]
Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at dfef0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Capabilities: [70] AGP version 2.0
Bus 004 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.12 ehci_hcd
iProduct 2 VIA Technologies, Inc. USB 2.0
iSerial 1 0000:00:10.3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 6
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0001.0000 C_CONNECT
Port 2: 0000.0100 power
Port 3: 0001.0000 C_CONNECT
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 003 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.12 uhci_hcd
iProduct 2 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
iSerial 1 0000:00:10.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0001
Self Powered
Bus 002 Device 003: ID 107f:0001 KidzMouse, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x107f KidzMouse, Inc.
idProduct 0x0001
bcdDevice 0.01
iManufacturer 1 KidzMouse, Inc. - www.KidzMouse.com
iProduct 2 KidzMouse Optical Mouse
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4 M2 ??
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 52
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 10
Device Status: 0x0000
(Bus Powered)
Bus 002 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.12 uhci_hcd
iProduct 2 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
iSerial 1 0000:00:10.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0303 lowspeed power enable connect
Port 2: 0000.0300 lowspeed power
Device Status: 0x0001
Self Powered
Bus 001 Device 004: ID 060b:0541 Solid Year
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x060b Solid Year
idProduct 0x0541
bcdDevice 1.01
iManufacturer 0
iProduct 1 USB Keyboard
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 59
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 1 Keyboard
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 54
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 0 No Subclass
bInterfaceProtocol 0 None
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 179
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0005 1x 5 bytes
bInterval 10
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.12 uhci_hcd
iProduct 2 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
iSerial 1 0000:00:10.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0303 lowspeed power enable connect
Port 2: 0000.0300 lowspeed power
Device Status: 0x0001
Self Powered
root@localhost:~# dmesg
Linux version 2.6.12 (root@Knoppix) (gcc-Version 3.3.6 (Debian 1:3.3.6-7)) #2 SMP Tue Aug 9 23:20:52 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000006000000 (usable)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
96MB LOWMEM available.
On node 0 totalpages: 24576
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 20480 pages, LIFO batch:7
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: Unable to locate RSDP
Allocating PCI resources starting at 06000000 (gap: 06000000:f8c00000)
Built 1 zonelists
Kernel command line: root=/dev/hda2 ro ramdisk_size=100000 lang=us apm=power-off nomce vga=791
No local APIC present or hardware disabled
mapped APIC to ffffd000 (011c1000)
Initializing CPU#0
PID hash table entries: 512 (order: 9, 8192 bytes)
Detected 796.212 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 88220k/98304k available (1882k kernel code, 9528k reserved, 999k data, 296k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1556.48 BogoMIPS (lpj=778240)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 00803035 80803035 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After all inits, caps: 00803135 80803035 00000000 00000000 00000000 00000000 00000000
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
CPU0: Centaur VIA Samuel 2 stepping 03
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
CPU0 attaching sched-domain:
domain 0: span 00000001
groups: 00000001
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 4058k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f7330
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x607b, dseg 0xf0000
PnPBIOS: Missing SMALL_TAG_ENDDEP tag
PnPBIOS: Missing SMALL_TAG_ENDDEP tag
PnPBIOS: Missing SMALL_TAG_ENDDEP tag
PnPBIOS: 12 nodes reported by PnP BIOS; 12 recorded by driver
SCSI subsystem initialized
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: Using IRQ router default [1106/3177] at 0000:00:11.0
PCI: IRQ 0 for device 0000:00:11.1 doesn't match PIRQ mask - try pci=usepirqmask
PCI: Hardcoded IRQ 14 for device 0000:00:11.1
audit: initializing netlink socket (disabled)
audit(1133884669.829:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
vesafb: framebuffer at 0xd8000000, mapped to 0xc6880000, using 3072k, total 32768k
vesafb: mode is 1024x768x16, linelength=2048, pages=20
vesafb: protected mode interface info at c000:403d
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
PCI: Hardcoded IRQ 14 for device 0000:00:11.1
PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 14
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: ST320014A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63
hda: cache flushes supported
hda: hda1 hda2 hda3
libata version 1.11 loaded.
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 256 buckets, 4Kbytes
TCP established hash table entries: 4096 (order: 4, 65536 bytes)
TCP bind hash table entries: 4096 (order: 3, 49152 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
NET: Registered protocol family 1
NET: Registered protocol family 15
RAMDISK: Compressed image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 296k freed
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
Warning: /proc/ide/hd?/settings interface is obsolete, and will be removed soon!
EXT3 FS on hda2, internal journal
Adding 192772k swap on /dev/hda3. Priority:-1 extents:1
EXT3 FS on hda2, internal journal
Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1: LSR safety check engaged!
ttyS1: LSR safety check engaged!
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 11, io base 0x0000e400
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 9, io base 0x0000e800
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 12, io base 0x0000ec00
usb 1-2: new low speed USB device using uhci_hcd and address 2
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 2-1: new low speed USB device using uhci_hcd and address 2
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ieee1394: Initialized config rom entry `ip1394'
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1)
Registering unionfs 20050921-1517
Real Time Clock Driver v1.12
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ts: Compaq touchscreen protocol output
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
usbcore: registered new driver hiddev
input: USB HID v1.10 Keyboard [USB Keyboard] on usb-0000:00:10.0-2
input,hiddev96: USB HID v1.10 Mouse [USB Keyboard] on usb-0000:00:10.0-2
input: USB HID v1.10 Mouse [KidzMouse, Inc. - www.KidzMouse.com KidzMouse Optical Mouse] on usb-0000:00:10.1-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA CLE266 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
eth0: VIA Rhine II at 0xdffffe00, 00:11:5b:ff:da:d7, IRQ 11.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1.
NET: Registered protocol family 17
loop: loaded (max 8 devices)
Via 686a/8233/8235 audio driver 1.9.1-ac4-2.5
via82cxxx: Six channel audio available
PCI: Setting latency timer of device 0000:00:11.5 to 64
ac97_codec: AC97 codec, id: CMI131 (Unknown)
via82cxxx: Codec rate locked at 48Khz
via82cxxx: board #1 at 0xE000, IRQ 12
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
ehci_hcd 0000:00:10.3: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: irq 10, io mem 0xdfffff00
ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
usb 1-2: USB disconnect, address 2
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 2-1: USB disconnect, address 2
usb 1-2: new low speed USB device using uhci_hcd and address 3
input: USB HID v1.10 Keyboard [USB Keyboard] on usb-0000:00:10.0-2
input,hiddev96: USB HID v1.10 Mouse [USB Keyboard] on usb-0000:00:10.0-2
usb 2-1: new low speed USB device using uhci_hcd and address 3
input: USB HID v1.10 Mouse [KidzMouse, Inc. - www.KidzMouse.com KidzMouse Optical Mouse] on usb-0000:00:10.1-1
NET: Registered protocol family 23
can't register device seq
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
lp0: using parport0 (interrupt-driven).
lp0: console ready
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0381d00(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
usb 1-2: USB disconnect, address 3
usb 1-1: new low speed USB device using uhci_hcd and address 4
input: USB HID v1.10 Keyboard [USB Keyboard] on usb-0000:00:10.0-1
input,hiddev96: USB HID v1.10 Mouse [USB Keyboard] on usb-0000:00:10.0-1
When I cat /dev/input/mice or /dev/input/event1, etc and move finger on touchpad I get no "jibberish" as expected.
Here is some more info...
From /proc/bus/input/devices
I: Bus=0003 Vendor=060b Product=0541 Version=0101
N: Name="USB Keyboard"
P: Phys=usb-0000:00:10.0-1/input0
H: Handlers=kbd event0
B: EV=120003
B: KEY=10000 7 ff800000 7ff febeffdf f3cfffff ffffffff fffffffe
B: LED=7
I: Bus=0003 Vendor=060b Product=0541 Version=0101
N: Name="USB Keyboard"
P: Phys=usb-0000:00:10.0-1/input1
H: Handlers=kbd mouse0 event1 ts0
B: EV=7
B: KEY=1fffff 0 0 3878 d801d101 1e0000 0 0 0
B: REL=103
root@localhost:~# lspci -v
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8623 [Apollo CLE266]
Subsystem: VIA Technologies, Inc.: Unknown device 0000
Flags: bus master, 66MHz, medium devsel, latency 8
Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Capabilities: [c0] Power Management version 2
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: dde00000-dfefffff
Prefetchable memory behind bridge: d5d00000-ddcfffff
Capabilities: [80] Power Management version 2
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at e400 [size=32]
Capabilities: [80] Power Management version 2
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Flags: bus master, medium devsel, latency 32, IRQ 9
I/O ports at e800 [size=32]
Capabilities: [80] Power Management version 2
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Flags: bus master, medium devsel, latency 32, IRQ 12
I/O ports at ec00 [size=32]
Capabilities: [80] Power Management version 2
0000:00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at dfffff00 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: VIA Technologies, Inc.: Unknown device 0000
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management version 2
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
Flags: bus master, medium devsel, latency 32, IRQ 14
I/O ports at fc00 [size=16]
Capabilities: [c0] Power Management version 2
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
Subsystem: Elitegroup Computer Systems: Unknown device a101
Flags: medium devsel, IRQ 12
I/O ports at e000 [size=256]
Capabilities: [c0] Power Management version 2
0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet Controller on VT8235
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at dc00 [size=256]
Memory at dffffe00 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
0000:01:00.0 VGA compatible controller: VIA Technologies, Inc. VT8623 [Apollo CLE266] integrated CastleRock graphics (rev 03) (prog-if 00 [VGA])
Subsystem: VIA Technologies, Inc. VT8623 [Apollo CLE266] integrated CastleRock graphics
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 11
Memory at d8000000 (32-bit, prefetchable) [size=64M]
Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at dfef0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Capabilities: [70] AGP version 2.0
Bus 004 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.12 ehci_hcd
iProduct 2 VIA Technologies, Inc. USB 2.0
iSerial 1 0000:00:10.3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 6
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0001.0000 C_CONNECT
Port 2: 0000.0100 power
Port 3: 0001.0000 C_CONNECT
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 003 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.12 uhci_hcd
iProduct 2 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
iSerial 1 0000:00:10.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0001
Self Powered
Bus 002 Device 003: ID 107f:0001 KidzMouse, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x107f KidzMouse, Inc.
idProduct 0x0001
bcdDevice 0.01
iManufacturer 1 KidzMouse, Inc. - www.KidzMouse.com
iProduct 2 KidzMouse Optical Mouse
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4 M2 ??
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 52
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 10
Device Status: 0x0000
(Bus Powered)
Bus 002 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.12 uhci_hcd
iProduct 2 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
iSerial 1 0000:00:10.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0303 lowspeed power enable connect
Port 2: 0000.0300 lowspeed power
Device Status: 0x0001
Self Powered
Bus 001 Device 004: ID 060b:0541 Solid Year
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x060b Solid Year
idProduct 0x0541
bcdDevice 1.01
iManufacturer 0
iProduct 1 USB Keyboard
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 59
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 1 Keyboard
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 54
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 0 No Subclass
bInterfaceProtocol 0 None
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 179
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0005 1x 5 bytes
bInterval 10
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.12 uhci_hcd
iProduct 2 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
iSerial 1 0000:00:10.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0303 lowspeed power enable connect
Port 2: 0000.0300 lowspeed power
Device Status: 0x0001
Self Powered
root@localhost:~# dmesg
Linux version 2.6.12 (root@Knoppix) (gcc-Version 3.3.6 (Debian 1:3.3.6-7)) #2 SMP Tue Aug 9 23:20:52 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000006000000 (usable)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
96MB LOWMEM available.
On node 0 totalpages: 24576
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 20480 pages, LIFO batch:7
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: Unable to locate RSDP
Allocating PCI resources starting at 06000000 (gap: 06000000:f8c00000)
Built 1 zonelists
Kernel command line: root=/dev/hda2 ro ramdisk_size=100000 lang=us apm=power-off nomce vga=791
No local APIC present or hardware disabled
mapped APIC to ffffd000 (011c1000)
Initializing CPU#0
PID hash table entries: 512 (order: 9, 8192 bytes)
Detected 796.212 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 88220k/98304k available (1882k kernel code, 9528k reserved, 999k data, 296k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1556.48 BogoMIPS (lpj=778240)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 00803035 80803035 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After all inits, caps: 00803135 80803035 00000000 00000000 00000000 00000000 00000000
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
CPU0: Centaur VIA Samuel 2 stepping 03
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
CPU0 attaching sched-domain:
domain 0: span 00000001
groups: 00000001
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 4058k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f7330
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x607b, dseg 0xf0000
PnPBIOS: Missing SMALL_TAG_ENDDEP tag
PnPBIOS: Missing SMALL_TAG_ENDDEP tag
PnPBIOS: Missing SMALL_TAG_ENDDEP tag
PnPBIOS: 12 nodes reported by PnP BIOS; 12 recorded by driver
SCSI subsystem initialized
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: Using IRQ router default [1106/3177] at 0000:00:11.0
PCI: IRQ 0 for device 0000:00:11.1 doesn't match PIRQ mask - try pci=usepirqmask
PCI: Hardcoded IRQ 14 for device 0000:00:11.1
audit: initializing netlink socket (disabled)
audit(1133884669.829:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
vesafb: framebuffer at 0xd8000000, mapped to 0xc6880000, using 3072k, total 32768k
vesafb: mode is 1024x768x16, linelength=2048, pages=20
vesafb: protected mode interface info at c000:403d
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
PCI: Hardcoded IRQ 14 for device 0000:00:11.1
PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 14
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: ST320014A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63
hda: cache flushes supported
hda: hda1 hda2 hda3
libata version 1.11 loaded.
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 256 buckets, 4Kbytes
TCP established hash table entries: 4096 (order: 4, 65536 bytes)
TCP bind hash table entries: 4096 (order: 3, 49152 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
NET: Registered protocol family 1
NET: Registered protocol family 15
RAMDISK: Compressed image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 296k freed
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
Warning: /proc/ide/hd?/settings interface is obsolete, and will be removed soon!
EXT3 FS on hda2, internal journal
Adding 192772k swap on /dev/hda3. Priority:-1 extents:1
EXT3 FS on hda2, internal journal
Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1: LSR safety check engaged!
ttyS1: LSR safety check engaged!
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 11, io base 0x0000e400
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 9, io base 0x0000e800
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 12, io base 0x0000ec00
usb 1-2: new low speed USB device using uhci_hcd and address 2
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 2-1: new low speed USB device using uhci_hcd and address 2
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ieee1394: Initialized config rom entry `ip1394'
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1)
Registering unionfs 20050921-1517
Real Time Clock Driver v1.12
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ts: Compaq touchscreen protocol output
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
usbcore: registered new driver hiddev
input: USB HID v1.10 Keyboard [USB Keyboard] on usb-0000:00:10.0-2
input,hiddev96: USB HID v1.10 Mouse [USB Keyboard] on usb-0000:00:10.0-2
input: USB HID v1.10 Mouse [KidzMouse, Inc. - www.KidzMouse.com KidzMouse Optical Mouse] on usb-0000:00:10.1-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA CLE266 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
eth0: VIA Rhine II at 0xdffffe00, 00:11:5b:ff:da:d7, IRQ 11.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1.
NET: Registered protocol family 17
loop: loaded (max 8 devices)
Via 686a/8233/8235 audio driver 1.9.1-ac4-2.5
via82cxxx: Six channel audio available
PCI: Setting latency timer of device 0000:00:11.5 to 64
ac97_codec: AC97 codec, id: CMI131 (Unknown)
via82cxxx: Codec rate locked at 48Khz
via82cxxx: board #1 at 0xE000, IRQ 12
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
ehci_hcd 0000:00:10.3: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: irq 10, io mem 0xdfffff00
ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
usb 1-2: USB disconnect, address 2
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 2-1: USB disconnect, address 2
usb 1-2: new low speed USB device using uhci_hcd and address 3
input: USB HID v1.10 Keyboard [USB Keyboard] on usb-0000:00:10.0-2
input,hiddev96: USB HID v1.10 Mouse [USB Keyboard] on usb-0000:00:10.0-2
usb 2-1: new low speed USB device using uhci_hcd and address 3
input: USB HID v1.10 Mouse [KidzMouse, Inc. - www.KidzMouse.com KidzMouse Optical Mouse] on usb-0000:00:10.1-1
NET: Registered protocol family 23
can't register device seq
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
lp0: using parport0 (interrupt-driven).
lp0: console ready
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0381d00(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
usb 1-2: USB disconnect, address 3
usb 1-1: new low speed USB device using uhci_hcd and address 4
input: USB HID v1.10 Keyboard [USB Keyboard] on usb-0000:00:10.0-1
input,hiddev96: USB HID v1.10 Mouse [USB Keyboard] on usb-0000:00:10.0-1