PDA

View Full Version : 1280 x 800 screen resolution



asearle
03-02-2006, 05:20 PM
I have an ASUS laptop with an ATI (Mobility Radion x700) graphics card and would like to get my system to format the screen to 1280 x 800.

As it is the screen happily displays a default VGA format which is OK but (of course) a bit 'stretched'.

The system doesn't seem to recognise the graphic card so in 'Hardware Information' I get the following ...

ATI Technologies Inc. Unknown device 565S (prog-if 00 [VGA])

Which I imagine is just telling me that the system has switched to a default graphic mode.

In the Control Centre I tried to select 1280 x 800 but this wasn't available (there were just three default modes).

So my question here is whether I can get XFree86 to output 1280 x 800 without recognising the graphics card or whether I really need to install a driver specific to my graphics card?

Any tips would be a great help to me.

Regards and thanks,
Alan Searle

ramaswamyps
03-15-2006, 05:15 PM
check xorg.conf in /etc/X11
the modes available is there.
the default is for long monitors
i use i810 video
my 15" monitor shows much longer windows than the monitor length even in 800x600 mode.
u may not gain much by installing any new drivers.
use lower mode and see

dosdragon
03-19-2006, 02:57 PM
Open a root window and type
kxconfig

pgk3734
05-21-2006, 06:58 AM
Yes kxconfig is a good program to set screen size (resolution). After I did this and logged out & in I found the the panel was about three inches
down from the top in my KDE desktop. When I try to move the panel to the bottom of the screen the mouse-over ERASES the panel. I even went
into Control Center and indicated proper panel position. The setting I wanted was 1280x1024 on this FPD1730 Gateway. I must also say that
I have on this box Fedora Core 5, Ubuntu 5, SuSE 10.0 and of course Knoppix 4 and all the other distros set the 1280x1024 with no problems.
Other info: XF86Config-4
Section "ServerLayout"
Identifier "XFree86 Configured"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
# PS/2 Mouse using /dev/input/mice in Kernel 2.6
# Serial Mouse not detected
InputDevice "USB Mouse" "CorePointer"
EndSection

Section "ServerFlags"
Option "AllowMouseOpenFail" "true"

EndSection

Section "Files"
RgbPath "/usr/X11R6/lib/X11/rgb"
ModulePath "/usr/X11R6/lib/modules"
FontPath "/usr/X11R6/lib/X11/fonts/misc:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/misc"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo"
FontPath "/usr/X11R6/lib/X11/fonts/PEX"
# Additional fonts: Locale, Gimp, TTF...
FontPath "/usr/X11R6/lib/X11/fonts/cyrillic"
# FontPath "/usr/X11R6/lib/X11/fonts/latin2/75dpi"
# FontPath "/usr/X11R6/lib/X11/fonts/latin2/100dpi"
# True type and type1 fonts are also handled via xftlib, see /etc/X11/XftConfig!
FontPath "/usr/X11R6/lib/X11/fonts/Type1"
FontPath "/usr/share/fonts/ttf/western"
FontPath "/usr/share/fonts/ttf/decoratives"
FontPath "/usr/share/fonts/truetype"
FontPath "/usr/share/fonts/truetype/openoffice"
FontPath "/usr/share/fonts/truetype/ttf-bitstream-vera"
FontPath "/usr/share/fonts/latex-ttf-fonts"
FontPath "/usr/X11R6/lib/X11/fonts/defoma/CID"
FontPath "/usr/X11R6/lib/X11/fonts/defoma/TrueType"
EndSection

Section "Module"
Load "ddc" # ddc probing of monitor
Load "GLcore"
Load "dbe"
Load "dri"
Load "extmod"
Load "glx"
Load "bitmap" # bitmap-fonts
Load "speedo"
Load "type1"
Load "freetype"
Load "record"
EndSection

Section "InputDevice"
Identifier "Keyboard0"
Driver "keyboard"
Option "CoreKeyboard"
Option "XkbRules" "xfree86"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"

EndSection

Section "InputDevice"
Identifier "Serial Mouse"
Driver "mouse"
Option "Protocol" "Microsoft"
Option "Device" "/dev/ttyS0"
Option "Emulate3Buttons" "true"
Option "Emulate3Timeout" "70"
Option "SendCoreEvents" "true"
EndSection

Section "InputDevice"
Identifier "PS/2 Mouse"
Driver "mouse"
Option "Protocol" "auto"
Option "ZAxisMapping" "4 5"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "true"
Option "Emulate3Timeout" "70"
Option "SendCoreEvents" "true"
EndSection

Section "InputDevice"
Identifier "USB Mouse"
Driver "mouse"
Option "Device" "/dev/input/mice"
Option "SendCoreEvents" "true"
Option "Protocol" "IMPS/2"
Option "ZAxisMapping" "4 5"
Option "Buttons" "5"
EndSection

# Auto-generated by KNOPPIX mkxf86config

Section "Monitor"
Identifier "Monitor0"
Option "DPMS" "true"
VendorName "Gateway"
ModelName "EV700"
HorizSync 30-69# DDC-probed
VertRefresh 50-110# DDC-probed
# 1280x1024 @ 74.00 Hz (GTF) hsync: 79.03 kHz; pclk: 136.57 MHz
Modeline "1280x1024_74.00" 136.57 1280 1368 1504 1728 1024 1025 1028 1068 -HSync +Vsync

# These are the DDC-probed settings reported by your monitor.
# 1024x768, 75.0Hz; hfreq=60.02, vfreq=75.03
ModeLine "1280x1024" 190.96 1280 1376 1520 1760 1024 1025 1028 1085 -HSync +Vsync
ModeLine "1024x768" 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync
# 800x600, 75.0Hz; hfreq=46.88, vfreq=75.00
ModeLine "800x600" 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync
# 800x600, 72.0Hz; hfreq=48.08, vfreq=72.19
ModeLine "800x600" 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync
# 800x600, 60.0Hz; hfreq=37.88, vfreq=60.32
ModeLine "800x600" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync
# 640x480, 75.0Hz; hfreq=37.50, vfreq=75.00
ModeLine "640x480" 31.50 640 656 720 840 480 481 484 500 -hsync -vsync
# 640x480, 60.0Hz; hfreq=31.47, vfreq=59.94
ModeLine "640x480" 25.17 640 648 744 784 480 482 484 509 -hsync -vsync
# Extended modelines with GTF timings
# 640x480 @ 100.00 Hz (GTF) hsync: 50.90 kHz; pclk: 43.16 MHz
ModeLine "640x480" 43.16 640 680 744 848 480 481 484 509 -HSync +Vsync
# 768x576 @ 60.00 Hz (GTF) hsync: 35.82 kHz; pclk: 34.96 MHz
ModeLine "768x576" 34.96 768 792 872 976 576 577 580 597 -HSync +Vsync
# 768x576 @ 72.00 Hz (GTF) hsync: 43.27 kHz; pclk: 42.93 MHz
ModeLine "768x576" 42.93 768 800 880 992 576 577 580 601 -HSync +Vsync
# 768x576 @ 75.00 Hz (GTF) hsync: 45.15 kHz; pclk: 45.51 MHz
ModeLine "768x576" 45.51 768 808 888 1008 576 577 580 602 -HSync +Vsync
# 768x576 @ 85.00 Hz (GTF) hsync: 51.42 kHz; pclk: 51.84 MHz
ModeLine "768x576" 51.84 768 808 888 1008 576 577 580 605 -HSync +Vsync
# 768x576 @ 100.00 Hz (GTF) hsync: 61.10 kHz; pclk: 62.57 MHz
ModeLine "768x576" 62.57 768 816 896 1024 576 577 580 611 -HSync +Vsync
# 800x600 @ 100.00 Hz (GTF) hsync: 63.60 kHz; pclk: 68.18 MHz
ModeLine "800x600" 68.18 800 848 936 1072 600 601 604 636 -HSync +Vsync
# 1024x768 @ 100.00 Hz (GTF) hsync: 81.40 kHz; pclk: 113.31 MHz
ModeLine "1024x768" 113.31 1024 1096 1208 1392 768 769 772 814 -HSync +Vsync
# 1152x864 @ 60.00 Hz (GTF) hsync: 53.70 kHz; pclk: 81.62 MHz
ModeLine "1152x864" 81.62 1152 1216 1336 1520 864 865 868 895 -HSync +Vsync
# 1152x864 @ 85.00 Hz (GTF) hsync: 77.10 kHz; pclk: 119.65 MHz
ModeLine "1152x864" 119.65 1152 1224 1352 1552 864 865 868 907 -HSync +Vsync
# 1152x864 @ 100.00 Hz (GTF) hsync: 91.50 kHz; pclk: 143.47 MHz
ModeLine "1152x864" 143.47 1152 1232 1360 1568 864 865 868 915 -HSync +Vsync
# 1280x960 @ 72.00 Hz (GTF) hsync: 72.07 kHz; pclk: 124.54 MHz
ModeLine "1280x960" 124.54 1280 1368 1504 1728 960 961 964 1001 -HSync +Vsync
# 1280x960 @ 75.00 Hz (GTF) hsync: 75.15 kHz; pclk: 129.86 MHz
ModeLine "1280x960" 129.86 1280 1368 1504 1728 960 961 964 1002 -HSync +Vsync
# 1280x960 @ 100.00 Hz (GTF) hsync: 101.70 kHz; pclk: 178.99 MHz
ModeLine "1280x960" 178.99 1280 1376 1520 1760 960 961 964 1017 -HSync +Vsync
# 1280x1024 @ 100.00 Hz (GTF) hsync: 108.50 kHz; pclk: 190.96 MHz
ModeLine "1280x1024" 190.96 1280 1376 1520 1760 1024 1025 1028 1085 -HSync +Vsync
# 1400x1050 @ 60.00 Hz (GTF) hsync: 65.22 kHz; pclk: 122.61 MHz
ModeLine "1400x1050" 122.61 1400 1488 1640 1880 1050 1051 1054 1087 -HSync +Vsync
# 1400x1050 @ 72.00 Hz (GTF) hsync: 78.77 kHz; pclk: 149.34 MHz
ModeLine "1400x1050" 149.34 1400 1496 1648 1896 1050 1051 1054 1094 -HSync +Vsync
# 1400x1050 @ 75.00 Hz (GTF) hsync: 82.20 kHz; pclk: 155.85 MHz
ModeLine "1400x1050" 155.85 1400 1496 1648 1896 1050 1051 1054 1096 -HSync +Vsync
# 1400x1050 @ 85.00 Hz (GTF) hsync: 93.76 kHz; pclk: 179.26 MHz
ModeLine "1400x1050" 179.26 1400 1504 1656 1912 1050 1051 1054 1103 -HSync +Vsync
# 1400x1050 @ 100.00 Hz (GTF) hsync: 111.20 kHz; pclk: 214.39 MHz
ModeLine "1400x1050" 214.39 1400 1512 1664 1928 1050 1051 1054 1112 -HSync +Vsync
# 1600x1200 @ 100.00 Hz (GTF) hsync: 127.10 kHz; pclk: 280.64 MHz
ModeLine "1600x1200" 280.64 1600 1728 1904 2208 1200 1201 1204 1271 -HSync +Vsync
# 1920x1200 @ 60.00 Hz (GTF) hsync: 74.52; pclk: 193.16 MHz
Modeline "1920x1200" 193.16 1920 2048 2256 2592 1200 1201 1204 1242 -HSync +HSync
ModeLine "1280x1024/61Hz" 110 1280 1328 1512 1712 1024 1025 1028 1054
ModeLine "1280x1024/74Hz" 135 1280 1312 1456 1712 1024 1027 1030 1064
EndSection

Section "Device"
### Available Driver options are:-
# sw_cursor is needed for some ati and radeon cards
#Option "sw_cursor"
#Option "hw_cursor"
#Option "NoAccel"
#Option "ShowCache"
#Option "ShadowFB"
#Option "UseFBDev"
#Option "Rotate"
Identifier "Card0"
# The following line is auto-generated by KNOPPIX mkxf86config
Driver "fbdev"
VendorName "Generic"
BoardName "fbdev"
# BusID "PCI:1:0:0"
EndSection

Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
# DefaultColorDepth 16
SubSection "Display"
Depth 1
Modes "1280x1024/61Hz" "640x480"
Virtual 0 0
EndSubSection
SubSection "Display"
Depth 4
Modes "1280x1024/61Hz" "640x480"
Virtual 0 0
EndSubSection
SubSection "Display"
Depth 8
Modes "1280x1024/61Hz" "640x480"
Virtual 0 0
EndSubSection
SubSection "Display"
Depth 15
Modes "1280x1024/61Hz" "640x480"
Virtual 0 0
EndSubSection
SubSection "Display"
Depth 16
Modes "1280x1024/61Hz" "640x480"
Virtual 0 0
EndSubSection
SubSection "Display"
Depth 24
Modes "1280x1024/61Hz" "640x480"
Virtual 0 0
EndSubSection
SubSection "Display"
Depth 32
Modes "1280x1024/61Hz" "640x480"
Virtual 0 0
EndSubSection
EndSection

Section "DRI"
Mode 0666
EndSection

Section "InputDevice"

Identifier "Mouse"

Option "Protocol" ""
Option "Device" "/dev/mouse"
Driver "mouse"
Option "Emulate3Buttons"
Option "ZAxisMapping" "4 5"
EndSection

I have done much work by myself and it's time for me to ask kindly for help; perhaps from someone who had this problem
and will post the fix.
tia
pgk