CJWertz
06-26-2006, 09:20 PM
I posted once before witb much less information. Essentially, I'm trying to get a linksys wmp54g wireless card to work with knoppix. I've tried a few things and read several forum posts. I'm still lost. It may be I just don't know enough.
- - - - - - - - -
When I try to start knoppix 5.0.1 (CD - KNOPPIX_V5.0.1CD-2006-06-01-EN.iso) and it reaches the networking part, it says:
eth0 detected
dhcp broadcasting for ip
udevd - event[3258]: wait for sysfs: waiting for 'sys/class/net/eth0/device/driver' failed
Nothing seems to happen after that. I'm stuck.
- - - - - - - -
I tried starting with the nodhcp cheat code.
It goes a little further, but the last thing I see is this
probing/loading agp modules udevd_event[3391]: wait for sysfs: waiting for '/sys/c;ass/net/eth0/device/driver' failed.
- - - - - - - - -
So, I downloaded version 4.0.2 (CD - KNOPPIX_V4.0.2CD-2005-09-23-EN.iso)
It also hangs if I start without the nodhcp code. Instead of returning an error, it just goes off and never returns.
It does start with nodhcp.
I tried some things I found in a forum
I then run iwconfig eth0 essid "my ssid"
That seems to work.
iwconfig returns this
lo no wireless extension
eth0 RT2500 Wireliess ESSID: "My ssid"
Mode managed Frequency=2.412GHz Bit Rate: 1mb/s
RTS thr:off Fragment thr:off
Linkquality 0/100 Signal level=-120dbm noiselevel: -256dBm
Rx invalid nwid:0 Rx Invalid crypt:0 Rxinvalid frag: 0
Tx Excessive retries:0 Invalid misc:0 beacon:0
I try pump -i ath0.
It hangs. No error. Nothing.
I also tried configuring the network card from the knoppix menu to no avail. That ends up hanging.
The relevant (I think) output from lspci -v is
Network controller:Ralink Ralink RT2500 802.11 Cardbus Reference Card (rev 01)
Subsystem:Linksys:unknown device 0032
Flags:busmaster, slow devsel, latency 32, IRQ=11
memory at ea000000 (32 bit non prefetchable) [size=8k]
capabilities:[40] powermanagement version 2
- - - - - - - - -
When I try to start knoppix 5.0.1 (CD - KNOPPIX_V5.0.1CD-2006-06-01-EN.iso) and it reaches the networking part, it says:
eth0 detected
dhcp broadcasting for ip
udevd - event[3258]: wait for sysfs: waiting for 'sys/class/net/eth0/device/driver' failed
Nothing seems to happen after that. I'm stuck.
- - - - - - - -
I tried starting with the nodhcp cheat code.
It goes a little further, but the last thing I see is this
probing/loading agp modules udevd_event[3391]: wait for sysfs: waiting for '/sys/c;ass/net/eth0/device/driver' failed.
- - - - - - - - -
So, I downloaded version 4.0.2 (CD - KNOPPIX_V4.0.2CD-2005-09-23-EN.iso)
It also hangs if I start without the nodhcp code. Instead of returning an error, it just goes off and never returns.
It does start with nodhcp.
I tried some things I found in a forum
I then run iwconfig eth0 essid "my ssid"
That seems to work.
iwconfig returns this
lo no wireless extension
eth0 RT2500 Wireliess ESSID: "My ssid"
Mode managed Frequency=2.412GHz Bit Rate: 1mb/s
RTS thr:off Fragment thr:off
Linkquality 0/100 Signal level=-120dbm noiselevel: -256dBm
Rx invalid nwid:0 Rx Invalid crypt:0 Rxinvalid frag: 0
Tx Excessive retries:0 Invalid misc:0 beacon:0
I try pump -i ath0.
It hangs. No error. Nothing.
I also tried configuring the network card from the knoppix menu to no avail. That ends up hanging.
The relevant (I think) output from lspci -v is
Network controller:Ralink Ralink RT2500 802.11 Cardbus Reference Card (rev 01)
Subsystem:Linksys:unknown device 0032
Flags:busmaster, slow devsel, latency 32, IRQ=11
memory at ea000000 (32 bit non prefetchable) [size=8k]
capabilities:[40] powermanagement version 2