PDA

View Full Version : PCI: Cannot allocate resource region 4 of device 00:07.1


nono
06-17-2003, 11:15 AM
Hello,

I have been booting from VMWARE (iso of KNOPPIX) since that is the only way I can boot from my laptop.

When Knoppix is being launched, I'm getting the following message :

Error: only one processor found
PCI: Cannot allocate resource region 4 of device 00:07.1

what can I do resolve this ?

Thank you!
Dave_Bechtel
06-17-2003, 02:57 PM
--I get the same error under vmware emulation. It means that Knoppix detected some hardware on the host system but can't activate it because it doesn't "own" the hardware like it would if you were booting it natively. On my system, this happens to the Adaptec SCSI card.

--Don't worry about it unless Knoppix fails to boot after that error, and try the cheat codes if it is failing.


Hello,

I have been booting from VMWARE (iso of KNOPPIX) since that is the only way I can boot from my laptop.

When Knoppix is being launched, I'm getting the following message :

Error: only one processor found
PCI: Cannot allocate resource region 4 of device 00:07.1

what can I do resolve this ?

Thank you!
aay
06-17-2003, 05:20 PM
You could try this cheat code:

"knoppix nosmp"

That may alleviate your problem.
nono
06-17-2003, 07:31 PM
Thank you all for your help.

Here are the results :

by typing "koppinx nosmp" I get the "error only one pricessor found" to disappear which is good news,

Yet, the meesge about " cannot allocate ressource ...blah balh" is still there.

Would you think of any other cheat codes that would work? Itried many of them.

Thanks!
Joanna.
aay
06-17-2003, 08:37 PM
Have you tried the "failsafe" option? That will disable as much as possible and then you can try and reenable things one by one.
rickenbacherus
06-18-2003, 03:58 AM
Ouch!- Dev 00:07:1 is your IDE interface. How about some hardware details?
nono
06-18-2003, 11:40 AM
Hello,

Thanks, I tried faisafe as well...in vain.

IDE info :
Name Intel(r) 82801CAM Ultra ATA Storage Controller-248A
Manufacturer Intel
Status OK
PNP Device ID PCI\VEN_8086&DEV_248A&SUBSYS_248A0E11&REV_01\3&61AAA01&0&F9
I/O Port 0x00001820-0x0000182F
Memory Address 0xFEBFF800-0xFEBFFBFF
Driver c:\windows\system32\drivers\intelide.sys (5.1.2600.0 (XPClient.010817-1148), 4,50 KB (4 608 bytes), 17/08/2001 22:51)

Name Primary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&43B6552&0&0
I/O Port 0x000001F0-0x000001F7
I/O Port 0x000003F6-0x000003F6
IRQ Channel IRQ 14
Driver c:\windows\system32\drivers\atapi.sys (5.1.2600.0 (XPClient.010817-1148), 84,63 KB (86 656 bytes), 17/08/2001 22:51)

Name Secondary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&43B6552&0&1
I/O Port 0x00000170-0x00000177
I/O Port 0x00000376-0x00000376
IRQ Channel IRQ 15
Driver c:\windows\system32\drivers\atapi.sys (5.1.2600.0 (XPClient.010817-1148), 84,63 KB (86 656 bytes), 17/08/2001 22:51)



CDROM DRIVES"


Drive D:
Description CD-ROM Drive
Media Loaded No
Media Type CD-ROM
Name TOSHIBA DVD-ROM SD-C2502
Manufacturer (Standard CD-ROM drives)
Status OK
Transfer Rate Not Available
SCSI Target ID 1
PNP Device ID IDE\CDROMTOSHIBA_DVD-ROM_SD-C2502________________1011____\31343030303734303439 20202020202020202020
Driver c:\windows\system32\drivers\cdrom.sys (5.1.2600.0 (XPClient.010817-1148), 46,38 KB (47 488 bytes), 18/08/2001 21:00)

Drive G:
Description CD-ROM Drive
Media Loaded No
Media Type CD-ROM
Name MATSHITA UJDA330
Manufacturer (Standard CD-ROM drives)
Status OK
Transfer Rate Not Available
SCSI Target ID 0
PNP Device ID IDE\CDROMMATSHITA_UJDA330________________________1 .51____\5&2977E87F&0&0.0.0
Driver c:\windows\system32\drivers\cdrom.sys (5.1.2600.0 (XPClient.010817-1148), 46,38 KB (47 488 bytes), 18/08/2001 21:00)

Indeed, I have two cdrom slots. one is for my dvd player, the other for CDRW.

The laptop os Presario US 2700.


Let me know!
Thank you,
Joanna.