HotPlug / My fstab problem??

[Coume]

Hello,

I am not able to get the hotplug working...
I can see that I have an USB thing plugged but I cannot find a way to mount or access the data.

I am wondering if it could not be an error in my fstab


# /etc/fstab: filesystem table.
#
# filesystem mountpoint type options dump pass
/dev/hda3 / reiserfs defaults 0 1
/dev/hda6 none swap sw 0 0
proc /proc proc defaults 0 0
none /proc/bus/usb usbdevfs defaults 0 0
/dev/fd0 /floppy vfat defaults,user,noauto,showexec,umask=022 0 0
/dev/cdrom /cdrom iso9660 defaults,ro,user,noexec,noauto 0 0

# partitions found by Knoppix
#/dev/hda3 /mnt/hda3 reiserfs noauto,users,exec 0 0
/dev/hda1 /mnt/hda1 ntfs defaults,users,exec 0 0
/dev/hda5 /mnt/hda5 vfat defaults,users,exec,umask=000 0 0


Is it good the way of mounting the USB port? Where do I need to go to access the data of my USB device?

Regards
Ludo

[rickenbacherus]

If you haven't gotten this solved yet perhaps this will help. USB storage devices can be found at /dev/sda1 /dev/sda2 etc.

usbview in a terminal should show you your USB hub and what's connected to it.

cat /proc/bus/usb/devices

[aay]

Maybe it's me, but usbview hasn't been working for me for a few releases now. Even when I have usb devices plugged in and working, usbview doesn't work. In fact I get the following message:



Can not open the file /proc/bus/usb/devices

Verify that you have USB compiled into your kernel, have the USB core modules loaded, and have the usbdevfs filesystem mounted

Like I said, I get this message even when usb devices are plugged in and working fine so I'm reluctant to recommend usbview as a good way to check if usb devices are detected right now...unless someone else has an explanation as to what's going on.

[rickenbacherus]

Sounds like you don't have /proc in your fstab. proc is just a virtual filesystem that you can use to gain insight as to your system. It isn't actually necessary for USB to function. USBview is of course just a frontend for
cat /proc/bus/usb/devices. It certainly does a nice job of decifering. :)

Here's the line from my fstab:


proc /proc proc defaults 0 0


If you have /proc mounted USBview is very cool- it will show you when something gets plugged in or removed.

[Coume]

If you haven't gotten this solved yet perhaps this will help. USB storage devices can be found at /dev/sda1 /dev/sda2 etc.

usbview in a terminal should show you your USB hub and what's connected to it.

cat /proc/bus/usb/devices

hiya,
it did work for a time with the /dev/sda1 but now , it always says an error during the boot with my line in the fstab...

tonight, I 'll take my fstab and tomorrow I'll put it here.. you might se the error in my line with the /dev/sda1 ...

Thxs
Ludo

[Coume]

Here is my fstab:


# /etc/fstab: filesystem table.
#
# filesystem mountpoint type options dump pass
/dev/hda3 / reiserfs defaults 0 0

/dev/hda1 /mnt/hda1 ntfs defaults,users,exec 0 0

/dev/hda5 /mnt/hda5 vfat defaults,users,exec,umask=000,gid=disk 0 0
/dev/hda6 none swap sw 0 0
proc /proc proc defaults 0 0
none /proc/bus/usb usbdevfs defaults 0 0
/dev/fd0 /floppy vfat defaults,users,noauto,showexec,umask=022 0 0
/dev/cdrom /cdrom iso9660 defaults,users,noexec,noauto 0 0
/dev/sda1 /mnt/usb vfat defaults 0 0


and here are the errors that I get:


mount: /dev/sda1 is not a valid block device
modprobe: modprobe: can't locate module block-major 8


Have you got an idea/solution for this ones??

thxs
Ludo

[donl]

I did this to get usb working after 7-26-03 hdinstall.

mkdir /mnt/sda1 (only if sda1 doesn't exist)

edited the /etc/fstab file by adding:

/dev/sda1/ /mnt/sda1 vfat noauto,users,exec,unmask 0 0

Do this if don't know to edit: sudo kwrite file:/etc/fstab

Make Usb icon on desktop and click to view usb drive.