balaclavabob
09-07-2003, 04:36 PM
Hello,
I did a hdd install of Knoppix 3.1 and the cd burner (liteon 52x24x52x) worked fine using the 2.4.20-xfs kernel. The burner was scd0 under /dev.
But when I upgraded my kernel to 2.4.21, the burner doesn't work, I cannot even read from it or write to it. I have tried to read lots of different cds, ones which used to work.
root@box:/# mount /dev/scd0 /cdrom
mount: /dev/scd0 is not a valid block device
root@box:/# mount /dev/hdd /cdrom
mount: /dev/hdd: can't read superblock
root@box:/# ls -al /dev/cdrom
lrwxrwxrwx 1 root root 3 Aug 16 23:54 /dev/cdrom -> sr0
root@box:/# ls -al /dev/hdd
brw-rw---- 1 root disk 22, 64 Apr 15 2001 /dev/hdd
root@box:/# ls -al /dev/scd0
brw-rw---- 1 root cdrom 11, 0 May 31 2001 /dev/scd0
root@box:/# dmesg
Linux version 2.4.21 (root@box) (gcc version 3.2.1 20020924 (Debian prerelease)) #1 Sun Aug 24 14:13:28 WST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 0000000000080000 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001dfec000 (usable)
BIOS-e820: 000000001dfec000 - 000000001dfef000 (ACPI data)
BIOS-e820: 000000001dfef000 - 000000001dfff000 (reserved)
BIOS-e820: 000000001dfff000 - 000000001e000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
479MB LOWMEM available.
On node 0 totalpages: 122860
zone(0): 4096 pages.
zone(1): 118764 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=Linux ro root=302 hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi apm=power-off nomce
ide_setup: hda=scsi
ide_setup: hdb=scsi
ide_setup: hdc=scsi
ide_setup: hdd=scsi
ide_setup: hde=scsi
ide_setup: hdf=scsi
ide_setup: hdg=scsi
ide_setup: hdh=scsi
Found and enabled local APIC!
Initializing CPU#0
Detected 1595.891 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3185.04 BogoMIPS
Memory: 483208k/491440k available (1505k kernel code, 7720k reserved, 559k data, 112k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
CPU: AMD Athlon(TM) XP 1900+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1595.9056 MHz.
..... host bus clock speed is 265.9843 MHz.
cpu: 0, clocks: 2659843, slice: 1329921
CPU0<T0:2659840,T1:1329904,D:15,S:1329921,C:2659843>
PCI: PCI BIOS revision 2.10 entry at 0xf1b20, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router default [10de/01b2] at 00:01.0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
PPP generic driver version 2.4.2
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 409M
agpgart: unsupported bridge
agpgart: no supported devices found.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: ST315320A, ATA DISK drive
hdd: LITE-ON LTR-52246S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: 29888820 sectors (15303 MB) w/2048KiB Cache, CHS=1860/255/63
ide-cd: passing drive hdd to ide-scsi emulation.
Partition check:
hda: hda1 hda2 hda3
ide-cd: passing drive hdd to ide-scsi emulation.
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
es1371: version v0.32 time 14:14:58 Aug 24 2003
usb.c: registered new driver hub
host/uhci.c: USB Universal Host Controller Interface driver v1.1
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 112k freed
Adding Swap: 489972k swap-space (priority -1)
PCI: Setting latency timer of device 00:04.0 to 64
Nvidia + AC97 Audio, version 0.24, 17:30:24 Aug 24 2003
Nvaudio: in Funcction Nvaudio_init_module
PCI: Enabling device 00:06.0 (0005 -> 0007)
PCI: Setting latency timer of device 00:06.0 to 64
Nvaudio: NVIDIA nForce1 Audio found at IO 0xe000 and 0xe100, IRQ 11
Nvaudio: Audio Controller supports 6 channels.
NVaudio: Defaulting to base 2 channel mode.
ac97_codec: AC97 Audio codec, id: ALG32 (ALC650)
Nvaudio: only 48Khz playback available.
Nvaudio: AC'97 codec 0 supports AMAP, total channels = 6
spurious 8259A interrupt: IRQ7.
/dev/vmmon: Module vmmon: registered with major=10 minor=165
/dev/vmmon: Module vmmon: initialized
/dev/vmnet: open called by PID 246 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: up
bridge-eth0: attached
/dev/vmnet: open called by PID 270 (vmnet-netifup)
/dev/vmnet: hub 1 does not exist, allocating memory.
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 269 (vmnet-natd)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 288 (vmnet-dhcpd)
/dev/vmnet: port on hub 1 successfully opened
ttyS: 1 input overrun(s)
ide-cd: passing drive hdd to ide-scsi emulation.
ide-cd: passing drive hdd to ide-scsi emulation.
ide-cd: passing drive hdd to ide-scsi emulation.
ide-cd: passing drive hdd to ide-scsi emulation.
I think i have to re-run some program which will fix this, but I don't know what. I have never set up a burner under linux before.
Thanks
Balaclava BoB
I did a hdd install of Knoppix 3.1 and the cd burner (liteon 52x24x52x) worked fine using the 2.4.20-xfs kernel. The burner was scd0 under /dev.
But when I upgraded my kernel to 2.4.21, the burner doesn't work, I cannot even read from it or write to it. I have tried to read lots of different cds, ones which used to work.
root@box:/# mount /dev/scd0 /cdrom
mount: /dev/scd0 is not a valid block device
root@box:/# mount /dev/hdd /cdrom
mount: /dev/hdd: can't read superblock
root@box:/# ls -al /dev/cdrom
lrwxrwxrwx 1 root root 3 Aug 16 23:54 /dev/cdrom -> sr0
root@box:/# ls -al /dev/hdd
brw-rw---- 1 root disk 22, 64 Apr 15 2001 /dev/hdd
root@box:/# ls -al /dev/scd0
brw-rw---- 1 root cdrom 11, 0 May 31 2001 /dev/scd0
root@box:/# dmesg
Linux version 2.4.21 (root@box) (gcc version 3.2.1 20020924 (Debian prerelease)) #1 Sun Aug 24 14:13:28 WST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 0000000000080000 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001dfec000 (usable)
BIOS-e820: 000000001dfec000 - 000000001dfef000 (ACPI data)
BIOS-e820: 000000001dfef000 - 000000001dfff000 (reserved)
BIOS-e820: 000000001dfff000 - 000000001e000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
479MB LOWMEM available.
On node 0 totalpages: 122860
zone(0): 4096 pages.
zone(1): 118764 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=Linux ro root=302 hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi apm=power-off nomce
ide_setup: hda=scsi
ide_setup: hdb=scsi
ide_setup: hdc=scsi
ide_setup: hdd=scsi
ide_setup: hde=scsi
ide_setup: hdf=scsi
ide_setup: hdg=scsi
ide_setup: hdh=scsi
Found and enabled local APIC!
Initializing CPU#0
Detected 1595.891 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3185.04 BogoMIPS
Memory: 483208k/491440k available (1505k kernel code, 7720k reserved, 559k data, 112k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
CPU: AMD Athlon(TM) XP 1900+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1595.9056 MHz.
..... host bus clock speed is 265.9843 MHz.
cpu: 0, clocks: 2659843, slice: 1329921
CPU0<T0:2659840,T1:1329904,D:15,S:1329921,C:2659843>
PCI: PCI BIOS revision 2.10 entry at 0xf1b20, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router default [10de/01b2] at 00:01.0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
PPP generic driver version 2.4.2
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 409M
agpgart: unsupported bridge
agpgart: no supported devices found.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: ST315320A, ATA DISK drive
hdd: LITE-ON LTR-52246S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: 29888820 sectors (15303 MB) w/2048KiB Cache, CHS=1860/255/63
ide-cd: passing drive hdd to ide-scsi emulation.
Partition check:
hda: hda1 hda2 hda3
ide-cd: passing drive hdd to ide-scsi emulation.
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
es1371: version v0.32 time 14:14:58 Aug 24 2003
usb.c: registered new driver hub
host/uhci.c: USB Universal Host Controller Interface driver v1.1
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 112k freed
Adding Swap: 489972k swap-space (priority -1)
PCI: Setting latency timer of device 00:04.0 to 64
Nvidia + AC97 Audio, version 0.24, 17:30:24 Aug 24 2003
Nvaudio: in Funcction Nvaudio_init_module
PCI: Enabling device 00:06.0 (0005 -> 0007)
PCI: Setting latency timer of device 00:06.0 to 64
Nvaudio: NVIDIA nForce1 Audio found at IO 0xe000 and 0xe100, IRQ 11
Nvaudio: Audio Controller supports 6 channels.
NVaudio: Defaulting to base 2 channel mode.
ac97_codec: AC97 Audio codec, id: ALG32 (ALC650)
Nvaudio: only 48Khz playback available.
Nvaudio: AC'97 codec 0 supports AMAP, total channels = 6
spurious 8259A interrupt: IRQ7.
/dev/vmmon: Module vmmon: registered with major=10 minor=165
/dev/vmmon: Module vmmon: initialized
/dev/vmnet: open called by PID 246 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: up
bridge-eth0: attached
/dev/vmnet: open called by PID 270 (vmnet-netifup)
/dev/vmnet: hub 1 does not exist, allocating memory.
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 269 (vmnet-natd)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 288 (vmnet-dhcpd)
/dev/vmnet: port on hub 1 successfully opened
ttyS: 1 input overrun(s)
ide-cd: passing drive hdd to ide-scsi emulation.
ide-cd: passing drive hdd to ide-scsi emulation.
ide-cd: passing drive hdd to ide-scsi emulation.
ide-cd: passing drive hdd to ide-scsi emulation.
I think i have to re-run some program which will fix this, but I don't know what. I have never set up a burner under linux before.
Thanks
Balaclava BoB