View Full Version : Drive CRC errors upon startup after HD install
allanorn
02-17-2004, 02:58 AM
Hi folks,
I've been having an issue with starting Knoppix 3.3 after I do a HD install.
Apparently I'm getting the following errors upon startup.
Configuring network interfaces ... usb_control/bulk_msg:timeout
input: USB HID V1.10 Keyboard [BTC Multimedia USB Keyboard] on usb1:3.0
Operation Failed.
Done.
<snip>
Cleaning: /tmp /var/lock /var/run
blk: queue c0334b60, limit 4095MB (0xfffffffff)
blk: queue c0334ca8, limit 4095MB (0xfffffffff)
hda: dma_intr: status=0x51 {DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 {DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 {DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 {DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
... and it hangs.
Any ideas? I've been working on this all day. Thanks in advance.
griffjon
02-23-2004, 06:04 PM
I'm having the same problem. I did a low-level format of the drive, and re-cfdisked (it's a clean HDD), and am stll encountering this error. I'm wondering if it is a bad CD burn?
fingers99
02-24-2004, 05:01 AM
I think it's more likely to be a cableing or jumpering error (though some here have suggested different remedies).
allanorn
02-24-2004, 07:39 AM
I've used this drive for years as a Windows drive, so I know it's not jumpering or cables. I'm wondering if I'm hitting a 4GB limitation somewhere since all the bitmasks are set to 1.
Stephen
02-24-2004, 07:58 AM
Hi folks,
I've been having an issue with starting Knoppix 3.3 after I do a HD install.
Apparently I'm getting the following errors upon startup.
Configuring network interfaces ... usb_control/bulk_msg:timeout
input: USB HID V1.10 Keyboard [BTC Multimedia USB Keyboard] on usb1:3.0
Operation Failed.
Done.
<snip>
Cleaning: /tmp /var/lock /var/run
blk: queue c0334b60, limit 4095MB (0xfffffffff)
blk: queue c0334ca8, limit 4095MB (0xfffffffff)
hda: dma_intr: status=0x51 {DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 {DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 {DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 {DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
... and it hangs.
Any ideas? I've been working on this all day. Thanks in advance.
Edit the file /etc/init.d/bootmisc.sh and near the bottom you should see a line with hdparm -d1 /dev/hda put a # character at the start of the line to comment it out. If this does not take care of the problem then your drive may be going bad you should get a testing program and find out. BTW in regards to your last post windows will happily accept a cable select for the jumpers, sometimes Linux will not they need to be set master or slave.
bsjawle
06-18-2004, 07:29 PM
I am getting similar error and would want to try out the suggestion. May be being a newbie I am missing something. After failing to boot due to above mentioned problem after HD install, I booted from LiveCD and tried to find hdparm line in /etc/init.d/bootmisc.sh but couldn't find any. I could find in knoppix-autoconfig though. I don't know whether I should be modifying it or whether I am looking into right place (as I am booting from CD)
Pls. advise.
symcbean
08-12-2004, 11:07 PM
Hi,
I might have solved the problem. I was setting up a used machine (formerly had Win98). I first went with SuSe but my install disks wouldn't read. Got sort of a working system but nothing to impress. Had a knoppix CD handy, so shoved it in and got it installed. Only problem was I was getting these errors regularly. I hadn't seen anything with Win98/SuSe but hadn't used either extensively, so I assumed it must be a hardware fault. Tried a new hard drive. Tried moving the hard drive from IDE0 to IDE1. To no avail.
I messed around with various other settings. Then looked at the kernel startup (in /etc/lilo.conf) - the command line contains hda=scsi hdb=scsi hdc=scsi.... Which was a new one to me. The kernel documentation didn't explain it, so I changed each entry to hdX=none except for the one disk which was installed which I changed to hdc=autotune. It's been running and in use for about 3 hours now without a single occurrence - but I'm still keeping my fingers crossed :?
HTH
jackiechen858
01-04-2005, 06:06 PM
Thanks for this message, I fixed it by changing the hd jumper from cable select to master. Also I still don't know why. The orignal redhad 6.2 works fine under calbe select. The Knoppix 3.4 pop up the CRC error, but it's still working without any other problem.
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.