Is there a Bit Torrent File/Server yet ?Originally Posted by aay
- removed some scsi modules from the regular knoppix26 (Kernel 2.6) startup
because they are unstable. Use "expert26" to load them.
- Added script for generating bootfloppies in Knoppix "Utilities" menu
- Harddisk installer update from Fabian Franz
- "knoppix splash" fixes
- timezone and language setting add-ons
- added linlinc1 for captive-ntfs for download capabilities
- changed some e100/eepro100 network driver entries in hardware detection
- the usual debian package updates
Is there a Bit Torrent File/Server yet ?Originally Posted by aay
hi you could find more downloads at this mirror page :
http://www.knopper.net/knoppix-mirrors/index-en.html
and for those use parameter "acpi=off" to boot kernel 2.6, you might also wish to try it with "acpi=ht"
Add acpi=ht, meaning run ACPI boot setup, but do not enable the interpreter.
A mirror that has the files ATM.
http://ftp.freenet.de/pub/ftp.uni-kl...linux/knoppix/
Torrent available from http://www.boegenielsen.dk:6969
Hi
as with the first 3.4 release I am not able to boot 2 PC's with the 2.6 kernel. Both of them boot properly with the 2.4 kernel.
With 2.6 the PC's freeze completely (not even Ctrl-Alt-Del work) on the network adapter:
...
Network device eth0 detected, DHCP broadcasting for IP
...
Both PC's have a Netgear FA310-TX card (DEC 2114x) which has worked with Xandros, Debian and Mandrake 10(with 2.6 kernel). With the 2.4 kernels it usually used the tulip driver from D.Becker but with Knoppix 3.4 and kernel 2.4 it actually uses:
...
eth0: DC21140 at 0xec00 (PCI bus 0, device 9), h/w address 00:40:05:42:c3:40,
and requires IRQ15 (provided by PCI BIOS).
de4x5.c:V0.546 2001/02/22 davies@maniac.ultranet.com
...
Will get Mandrake 10 back on one of these to see what they are using in their 2.6 kernel.
P.S. Mandrake 10 is using the tulip driver:
....
Linux Tulip driver version 1.1.13 (May 11, 2002)
PCI: Found IRQ 15 for device 0000:00:09.0
tulip0: EEPROM default media type Autosense.
tulip0: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block.
tulip0: MII transceiver #0 config 1000 status 782d advertising 01e1.
eth0: Digital DS21140 Tulip rev 34 at 0xec00, 00:40:05:42:C3:40, IRQ 15.
....
B
I'm no expert but maybe this will help.Originally Posted by bighusky
Knoppix 3.4 hung the first time I tried it and here's what worked for me (This is a combination of things I saw elsewhere in the forum
At boot: enter "linux26 knoppix noscsi"
This loads the Linux 2.6 kernel without SCSI detection, which is where Knoppix hung on my computer.
Is it possible to do an "upgrade" from the previous knoppix 3.4 iso to the current one without downloading the newer iso?
--
Brian
Unfortunately not. I guess, it would be possible to use rsync, if the image was compressed with an rsync-aware gzip (or zlib). This would increase the size of the image with a few percent. That could be a problem, because the size cannot grow much, if it should fit on a cd-rom
Well, not too worry, I have ADSL & rewriteable CDs!Originally Posted by tboege
But I think I'll wait a week or so until a more stable release of 3.4, rather than downloading a new one everyday!
regards
--
Brian
Juniper Networks EX3300 EX3300-48P PoE+ 48-Port 4x SFP Gigabyte Ethernet Switch
$59.99
Juniper EX 4300 EX4300-48P Gigabit Network Switch JunOS 21.4R3-S7 48 Port PoE
$249.00
Juniper EX3300-48P 48-Port 10/100/1000BASE-T (48 PoE+ ports) with 4 SFP+
$74.00
JUNIPER EX3400-48P 48x 1GB PoE+ RJ-45 4x 10GB SFP+ 2x 40GB QSFP+, DUAL AC POWER
$168.00
Juniper EX4200-48PX 48-PORT 10/100/1000BASET PoE Ethernet Switch
$50.00
Juniper Networks SRX320-POE 6-Port Service Gateway Security Appliance Tested
$149.99
Juniper 24-Port Gigabit Ethernet+ & 4-Port SFP Network Switch EX2200-24T-4G
$26.39
Juniper Networks EX2300-C-12T Compact 12-Port EX2300-C Series Ethernet Switch
$300.00
Juniper EX 4300 EX4300-48P Switch VC DAC Cables 21.4R3-S7 48 Port PoE
$250.00
(2) Juniper Networks EX2300 (EX2300-48P) 48 Ports Ethernet Switch+ Power Cord
$500.00