Is your card recognized?
Does it have an i.p.?Code:lspci
Can you bring up the interface w/ pump?Code:ifconfig eth0
What about restarting the network?Code:pump
Code:/etc/init.d/networking restart
Hi all, I'm italian (sorry for my english!).
I have a problem: I have installed knoppix 3.4 on my notebook's hard disk, but my network connection (LAN) doesn't work.
I have one integrated ethernet card that Knoppix recognize fine. I have dual boot: XP and Knoppix.
I write my IP, DNS and gateway, but I can't connect to our LAN.
Thanks in advance
Edgardo
Is your card recognized?
Does it have an i.p.?Code:lspci
Can you bring up the interface w/ pump?Code:ifconfig eth0
What about restarting the network?Code:pump
Code:/etc/init.d/networking restart
Hi, sorry for reply delay.
I had done lspci (see attach text with lspci + ifconfig eth0 + pump + restarting network).
I must re-configure every time the ethernet card with IP.DNS and gateway (you can see in the attach text that the first time my ethernet card is not recognized, then it is necessary to rewrite the configuration!)
root@box:/home/edgardo# lspci
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8378 [KM400] Chipset Host Bridge
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge
0000:00:07.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 02)
0000:00:08.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link)
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
0000:00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
0000:00:11.6 Communication controller: VIA Technologies, Inc. Intel 537 [AC97 Modem] (rev 80)
0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
0000:01:00.0 VGA compatible controller: VIA Technologies, Inc. VT8378 [S3 UniChrome] Integrated Video (rev 01)
root@box:/home/edgardo#
root@box:/home/edgardo# ifconfig eth0 (****note: it is the first time, then it is necessary to rewrite the configuration!)
eth0 Link encap:UNSPEC HWaddr 00-C0-9F-00-00-10-2A-98-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:2 dropped:2 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
root@box:/home/edgardo#
eth0 Link encap:UNSPEC HWaddr 00-C0-9F-00-00-10-2A-98-00-00-00-00-00-00-00-00
inet addr:192.168.0.205 Bcast:192.168.0.205 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:2 dropped:2 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
root@box:/home/edgardo#
root@box:/home/edgardo# pump
Operation failed.
root@box:/home/edgardo#
root@box:/home/edgardo# /etc/init.d/networking restart
Setting up IP spoofing protection: rp_filter.
Reconfiguring network interfaces...done.
root@box:/home/edgardo#
Thanks a lot!
Edgardo
Perhaps this post is of some assistance:
http://www.knoppix.net/forum/viewtopic.php?p=19004
Dear mzilikazi, I edited my /etc/network/interfaces.I have a static I.P,.you see:
# /etc/network/interfaces -- configuration file for ifup(, ifdown(
# The loopback interface
# automatically added when upgrading
auto lo eth0
iface lo inet loopback
iface eth0 inet static
address 192.168.0.205
netmask 255.255.255.0
network 192.168.0.0
broadcast 192.168.0.205
gateway 192.168.0.1
I re-installed knoppix but I can't connect to LAN. I have tried two hours.
Where do I a mistake? Where is the error(s)?
Thanks
Edgardo
Dear mzilikazi,
I found the problem: network card configuration program recognize TWO ethernet cards (eth0 and eth1): eth0 is my firewire (1394) eth1 is my ethernet card!!!
Now I set eth1 card and now it is all OK: I can access Internet.
Maybe this information is useful for notebook's users with firewire.
I apologized to you for not telling that my notebook have one firewire and one ethernet card, and that netconfig recognized two ethernet card.
Thanks a lot for your help
Edgardo
Glad you got it working! Also - thanks for posting how you solved the problem.![]()
Fanxiang SSD 4TB 2TB 1TB PS5 SSD M.2 NVME SSD 7300MBS PCIe 4.0 Solid State Drive
$259.99
Fanxiang 4TB 2TB 1TB SSD 550MB/s 2.5'' SATA III Internal Solid State Drive lot
$188.99
Netac 1TB 2TB 512GB Internal SSD 2.5'' SATA III 6Gb/s Solid State Drive lot
$119.99
4tb Ssd 870evo Internal Solid State Drive Hard Disk 2.5 Inch Sata SSD For Laptop
$47.79
Patriot P210 128GB 256GB 512GB 1TB 2TB 2.5" SATA 3 6GB/s Internal SSD PC/MAC Lot
$19.99
Patriot P300 128G 256GB 512GB 1TB 2TB M.2 2280 PCIe Gen3x4 NVMe Internal SSD Lot
$16.99
1080PRO 4TB SSD Solid State Hard Drive Ngff M.2 SSD Gaming Internal Hard Disk
$28.99
SSD 512GB 1/2/4TB 870 EVO SATA III SSD 2.5'' Solid State Drive Upgrade PC Laptop
$39.99
Fanxiang SSD 1TB 2TB 4TB Sata SSD Lot 2.5 512GB 256GB 6Gb/s Solid State Drive
$189.04
Fanxiang M.2 SATA SSD 2TB 1TB 512GB 256GB SSD Internal M2 Solid State Drive Lot
$109.99