Add those module names to /etc/modules (or /etc/modules-KERNEL-VERSION if it exists). These modules are loaded at each boot.
Hello,
some weeks ago I had installed Knoppix 3.3 on HDD and everything works fine. But at that time, the USB support was switched off in the BIOS. Thus, there are now as a result no USB modules available in my Knoppix HDD installation (the output of "dmesg" doesn't show anything about a USB driver).
How can I add the needed USB modules (probably usbcore, usb-uhci and usb-storage) to my system?
When I boot Knoppix from CD, my USB stick is at least found within the "K Info Centre" and the vendor name / serial number shown there. Hence, the hardware seems to be working. Yet, I could't mount the USB stick so far as there seem to be some additional filesystem problems.
But what I actually want is to use the USB stick with my existing Knoppix 3.3 HDD installation. What shall I do???
Thanks in advance for your help!
Oli
Add those module names to /etc/modules (or /etc/modules-KERNEL-VERSION if it exists). These modules are loaded at each boot.
Hi Kelmo,
if this was so easy, I'd be glad. But it isn't!
I tried insmod usb*, but it didn't find the usb-storage module. Then I found it somewhere deep in the directory tree and installed it there manually. But when I try to mount my usb stick on sda1, I always get the error message: "not a valid block device". sda4 is my Iomega ZIP drive which works fine.
As I wrote, the situation is a little bit different when booting from CD (Knoppix 3.3 or 3.4ct): Then, the USB stick is recognized correctly (as shown with "dmesg"), but Knoppix installs four SCSI devices, named sda1, 2, 3, and 4. sda4 should be my Iomega ZIP drive. However, if you try to mount any of the sda1...4 devices, you'll get the error message "filesystem could not be detected".
Please help!
Olivier
I believe that it is a problem with the partition table of the device that you are trying to mount. The mere fact that the filesystem is the trouble means that the device is being detected properly.
I cannot give any more info, because I am not 100% certain on how to correct this, but it is a problem with the partition table.
I have read other threads in this forum on the same topic.
Dell R730 w/ 2x E5-2650v3 10c, 192GB (12x16GB) RAM, H730 Mini, 2x 750W PSU
$499.99
Dell PowerEdge R720 Server - 2x8c CPU,256Gb RAM, 128Gb SSD/3x900Gb SAS, Proxmox
$340.00
Dell PowerEdge R340 w/ 1x Xeon E-2126G, 16GB (2x8) RAM, H730P
$500.00
$449.99
Dell PowerEdge R620 Server 2x E5-2660 v1 2.2GHz 16 Cores 256GB RAM 2x 300GB HDD
$89.99
Dell R630 Server 2x E5-2620 V4 2.1GHz =16 Cores 128GB DDR4 1x 960GB 2x 1G 2x 10G
$210.00
Dell PowerEdge R730XD 28 Core Server 2X Xeon E5-2680 V4 H730 128GB RAM No HDD
$389.99
DELL PowerEdge R730 Server 2x E5-2680v4 2.4GHz =28 Cores 32GB H730 4xRJ45
$284.00
HP ProLiant DL380 Gen9 8SFF Server - E5-2698 v3 - 32Cores - 128GB Ram - 1TB HDD
$299.00
HP ProLiant DL380 Gen9 16SFF 2x E5-2680v4 2.4GHz =28 Cores 64GB P840 4xRJ45
$353.00