-
Senior Member
registered user
bootloader timeout
How do you change the timeout time in the linux/debian bootloader. Now it is set for 3 seconds and that is not enough time.
Is it this 'edit or kedit /etc/lilo.conf' ?
Is this run from the shell console?
-
Re: bootloader timeout
Originally Posted by
rrfish72
How do you change the timeout time in the linux/debian bootloader. Now it is set for 3 seconds and that is not enough time.
Is it this 'edit or kedit /etc/lilo.conf' ?
Is this run from the shell console?
run "kedit /etc/lilo.conf" from a shell. This will open up a graphical editor and will open the file "/etc/lilo.conf" for editing.
edit: but you don't have to use kedit. You can use any text editor of your choosing.
-
You need to be root for this. Open a shell/terminal and do:
Code:
kdesu kedit /etc/lilo.conf (type in root passwd, make the changes and save&quit)
su (to become root)
lilo -v (to run lilo, needs to be done or it won't boot)
ctrl-d (to exit from superuser mode)
-
Senior Member
registered user
reply
Still cannot get that to work. Gives me an error message about application*.
This is what I get 'MUTEX DESTRIY FAILUE: DEVICE OR RESOURCE BUSY'
And an error box that says 'Command 'Kedit' not found'.
I can see the lilo.conf file but I can't open to edit. How do I edit the file??
-
kedit is not present in Knoppix 3.4
Try kwrite instead . . .
-
Sorry for the wrong info. As said, any editor present on the system will do.
-
Senior Member
registered user
reply
I used emacs and that worked. Also got in with vi.
-
Senior Member
registered user
reply
I still cannot get the timeout to change. I changed the delay to 1000 and still nothing. I did lilo -v after edit and no results. Any Ideas?
-
You need to change the timeout instead. This will give you a 5 sec timeout:
# Specifies the number of _tenths_ of a second LILO should
# wait before booting the first image. LILO
# doesn't wait if DELAY is omitted or if DELAY is set to zero.
delay=20
# Prompt to use certaing image. If prompt is specified without timeout,
# boot will not take place unless you hit RETURN
prompt
timeout=50
-
If you comment out timeout (see below) boot will not take place until you hit Enter.
# Specifies the number of _tenths_ of a second LILO should
# wait before booting the first image. LILO
# doesn't wait if DELAY is omitted or if DELAY is set to zero.
delay=20
# Prompt to use certaing image. If prompt is specified without timeout,
# boot will not take place unless you hit RETURN
prompt
# timeout=50
Similar Threads
-
By paoloskater in forum General Support
Replies: 1
Last Post: 02-02-2005, 02:42 PM
-
By ericia in forum Networking
Replies: 0
Last Post: 02-07-2004, 11:29 PM
-
By rdpetar in forum General Support
Replies: 1
Last Post: 12-09-2003, 10:44 PM
-
By quo_vadis in forum Hdd Install / Debian / Apt
Replies: 3
Last Post: 10-02-2003, 12:39 AM
-
By abc in forum Hardware & Booting
Replies: 0
Last Post: 03-22-2003, 02:41 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
TP-Link 24-Port Gigabit Ethernet Unmanaged Switch Desktop/Rackmount TL-SG1024D
$69.99
Dell X1018 X-Series Smart Managed Switches 16-Port Gigabit 2-Port SFP Switch
$42.00
CISCO MERAKI MS120-24P-HW 24-PORT GIGABIT CLOUD MANAGED PoE SWITCH - UNCLAIMED
$98.55
BrosTrend 8-Port 2.5G Ethernet Switch Multi-Gigabit Unmanaged Network Switch
$49.97
NETGEAR GS108 ProSafe 8-Port GbE Unmanaged Switch w/ Power Adapter
$14.99
Dell X1026P E11W 24-Port PoE Smart Managed Gigabit Ethernet Switch 2X SFP
$25.00
Dell X1052P Series 52-Port Gigabit Rack Mountable Managed Network Switch
$30.00
DELL 48 Port Gigabit Ethernet Network Switch POWERCONNECT 5548 FXP1R
$50.00
Cisco Nexus N3K-C3064PQ-10GX 48P 10GbE SFP+ 4P QSFP+ Switch (Fair)
$85.00
Fortinet FortiSwitch FS-124D-POE 24 Port Gigabit Ethernet Switch UNREGISTERED
$99.97