First thing, I don't have a clue why you want to run knoppix the hardway. Anyway it's your decision.
try this on root konsole:
mount /dev/hda6 /mnt/hda6
chroot /mnt/hda6
Then drag whatever you want.
Hope this will help
I'm in the process of putting knoppix on my HD, not installing just putting the live-cd on my HD. I read the HD based how to and followed the instructions to copy knoppix to HD & make the hd-copy bootable with LILO on HD.
1.2.1. Knoppix 3.4 version only
* Partition the harddisk to make room for knoppix:
o ext2 partition /dev/hda6 used to boot the kernel with lilo (10 Meg)
o ext2 partition /dev/hda7 for the knoppix image (I used 1000 Meg, but 800 Meg should be enough)
o swap partition /dev/hda8 (I used 256 Meg, but depends on your physical RAM)
o ext2 partition /dev/hda9 for the persistent home (any value you can spare)
* Boot the knoppix cd with the cheatcode "tohd=/dev/hda7". This will copy the knoppix image to disk.
* Reboot the knoppix cd with the cheatcode "fromhd=/dev/hda7" and check if it runs without the cd.
* Make the persistent homedir via the knoppix menu (penguin icon->configuration->make persistent dir).
* Do not save your KNOPPIX configuration via the menu, all changes to the environment will be saved automatically because of the persistent home.
* Copy the files from /boot to /mnt/hda6. Also copy the file "/mnt/cdrom/boot/isolinux/minirt24.gz" from the cd to /mnt/hda6.
* Copy /etc/lilo.conf to /mnt/hda6 and make the following boot entries (do not forget to uncomment the line with "prompt", or else the lilo boot menu will not appear):
image=/mnt/hda6/vmlinuz initrd=/mnt/hda6/minirt24.gz
append="fromhd=/dev/hda7 home=/dev/hda9 apm=power-off lang=nl hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi" root=/dev/hda7 label=Knoppix read-write
other=/dev/hda1
label=Windows98
* Mount the /mnt/hda6 partition temporary as /boot so lilo writes its map-file to the right place (sudo mount /dev/hda6 /boot)
* Let lilo write the boot loader to the master boot record (sudo lilo -C /mnt/hda6/lilo.conf)
* Remove the knoppix cd-rom and reboot. Now lilo will show you the menu and you can choose between win98 and knoppix.
* That's it. Enjoy.
I followed all the instructions up until it says to copy the files from /boot to /mnt/hd6, I'm trying to do this by dragging the files in the boot folder onto hd6 but it gives me an access denied. I made sure that the hd is mounted and writeable but it still happens. Can anyone help me do this, I also don't understand what it means to make a boot entry or the uncomment thing. I am totally new to linux and knoppix, so please use language I can understand. Thank you.
First thing, I don't have a clue why you want to run knoppix the hardway. Anyway it's your decision.
try this on root konsole:
mount /dev/hda6 /mnt/hda6
chroot /mnt/hda6
Then drag whatever you want.
Hope this will help
1TB/2TB USB 3.0 Flash Drive Thumb U Disk Memory Stick Pen PC Laptop Storage lot
$80.39
Type C USB 3.0 Flash Drive Thumb Drive Memory Stick for PC Laptop 1TB 2TB lot
$73.29
Seagate ST1000VM002 1TB 64MB SATA6Gb/s 3.5" (Low Power) Hard Drive -PC, CCTV DVR
$24.99
SAMSUNG PM981A SERIES 1TB TLC PCIE 3.0 X4 NVME M.2 2280 SSD | MZ-VLB1T0B
$49.99
CISCO A03-D1TBSATA 1TB 7.2K 6G 2.5INCH SATA HDD
$9.00
1TB HDD/SSD 2.5" SATA Hard Drive for Laptop with Win 10/Win 11 Pro Pre-installed
$27.99
Patriot P210 128GB 256GB 512GB 1TB 2TB 2.5" SATA 3 6GB/s Internal SSD PC/MAC Lot
$19.99
Samsung - Geek Squad Certified Refurbished 870 EVO 1TB SATA Solid State Drive
$67.99
SAMSUNG PM981 PCIE 3.0 NVME M.2 SSD | 1TB | MZ-VLB1T00
$49.99
Fanxiang SSD 4TB 2TB 1TB PS5 SSD M.2 NVME SSD 7300MBS PCIe 4.0 Solid State Drive
$259.99