-
Junior Member
registered user
needed to configure network printer.....
hallu all....
i need help on configuring/setting up printer. i am using a network printer and am now trying out using knoppix version 3.4. the kde printer wizard guided me along and when it came to a particular page, im stuck....
it asked for printer address--->is it the ip address of the printer or juz the name of the printer ?
it also asked for the port....again ?
there are a few options but i don really understand wat it wants.
i really need the printer configured....
if anyone could kindly help me, ur help is greatly appreciated...
thnx,
~ira~
-
Senior Member
registered user
In conjunction with the question for the port, I would bet it is the ip-adress.
For the correct port-number, I don't know.
If your printermanual hasn't a hint, or the manufactors web-page, you could try to use nmap, to scan the printer for open ports:
with printer_ip being 192.168.99.11 or whatever.
-
Senior Member
registered user
Hai again ira
I did some checking on printer server. The ip is actually the ip of the print server ( that small box) that connect from your hub/switch/router.... to your printer. If the box doesn't exist than it's not called printer server. So do the port, belongs to that box. Try googling on type of your print server and find the manual somewhere. Perhaps under your boss table.
-
Junior Member
registered user
hai user unknown & shah,
thnx for da reply ya....
will try it todae....
will let u nice guyz noe da results ya....
p.s: shah....im not allowed to go under ma boss' table....FORBIDDEN!
thnx again,
~ira~
-
Junior Member
registered user
-
Senior Member
registered user
-
Senior Member
registered user
631 is the port used by cups, the common unix printing system, to use.
So I woulnd't forget about that, but insert into the browser:
Code:
http:// 192.168.x.x:631/
That's at least the startingpoint for configuring the cups-printing system.
BTW: this singlish is very hard to understand for me. Could you try to use a language, where I find at least a dictionairy for?
-
Junior Member
registered user
ellu,
errm....
sorry ya....
i forgot to ask....
do i need to configure the network first?
psst user unknown,
im sorry if you dont really understand what im writing....
im just used to write that way in msn
terima kasih(thank you in malay)
~ira~
-
Senior Member
registered user
Kein Problem, ira, MSN erklärt natürlich so einiges...
You try to use a network printer, without having the network configured?
-
Junior Member
registered user
Similar Threads
-
By shantanuo in forum Networking
Replies: 0
Last Post: 09-20-2005, 05:52 AM
-
By brianfay in forum Hdd Install / Debian / Apt
Replies: 0
Last Post: 04-04-2005, 01:42 AM
-
By ebidder in forum MS Windows & New to Linux
Replies: 2
Last Post: 02-05-2005, 12:42 AM
-
By ptesone in forum Hardware & Booting
Replies: 0
Last Post: 03-16-2004, 08:25 PM
-
By urpk in forum General Support
Replies: 0
Last Post: 02-11-2004, 02:34 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Juniper Networks EX3300 EX3300-48P 48-Port Gigabit PoE+ Switch
$37.31
JUNIPER EX3400-48P 48x 1GB PoE+ RJ-45 4x 10GB SFP+ 2x 40GB QSFP+, DUAL AC POWER
$210.00
Juniper EX3300-48P 48-Port 10/100/1000BASE-T (48 PoE+ ports) with 4 SFP+
$74.00
Juniper EX3300-48P 48-Port 10/100/1000BASE-T 48 PoE+ 4 SFP+ 750-034250
$50.00
Juniper EX3300-48T EX3300 Series 48-Port 10/100/1000BASE-T no power cord
$40.00
Juniper Networks EX3300-24P | 24 Port Gigabit Network Switch w/ Power cord
$53.99
JUNIPER NETWORKS EX4600, 24 SFP+/SFP Ports, 4 QSFP+ Ports NETW
$3199.90
Juniper Ethernet Switch EX2200-C - 12 Port Switch
$89.99
Juniper Networks SRX345 Service Gateway 8 Port Gigabit 8 SFP 1G
$229.00
Juniper EX4500 40-Port 10GB SFP Managed Ethernet Switch P/N: EX4500-40F-VC1-FB
$199.99