need help with dmesg dump !

**HOfL** · 08-23-2004, 01:37 PM

HI
I installed Knoppix to hard drive last night, then upgraded using the testing mirrors , today I was going to complet the upgrade to sid , but before I did I ran dmseg and this was the output, would it be possable for some one to take a look at it. As It does not look right to me.
What is it looking for , why do I have eth1 not eth0 , fix my initscripts?.
The computer is a gericom Laptop with pentium4, ati9000mobilityradeon graphic card.

RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 276k freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
EXT3 FS on hda2, internal journal
Real Time Clock Driver v1.12
EXT3 FS on hda2, internal journal
warning: process `update' used the obsolete bdflush system call
Fix your initscripts?
ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX as device
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: TOSHIBA Model: DVD-ROM SD-R6012 Rev: 1031
Type: CD-ROM ANSI SCSI revision: 02
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
ACPI: AC Adapter [ADP0] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Processor [CPU0] (supports C1)
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
Yenta: CardBus bridge found at 0000:02:04.0 [156d:b730]
Yenta: ISA IRQ mask 0x0088, PCI irq 11
Socket status: 30000006
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:1f.2: Intel Corp. 82801BA/BAM USB (Hub #1)
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: irq 5, io base 00001400
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:1f.4: Intel Corp. 82801BA/BAM USB (Hub #2)
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: irq 11, io base 00001420
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1203 $ Ben Collins <bcollins@debian.org>
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[e0100000-e01007ff] Max Packet=[2048]
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
usbcore: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
usb 2-1: new low speed USB device using address 2
ts: Compaq touchscreen protocol output
Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled
ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:1f.4-1
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0050eb0200009e2b]
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x77

, irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
ip1394: $Rev: 1198 $ Ben Collins <bcollins@debian.org>
ip1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
Search for id