Knoppix does not include Smartlink modem drivers. You can build your own on a Hd-install, but some knowledge is needed. Some knoppix variants include many extra drivers, maybe look into one of them.
Recently got Knoppix_V3.4 (2004.05.17) live CD.
It does not recognize my dial-up modem.
It responds "KPPP Cannot find modem /dev/modem".
(The modem IS recognized and DOES work with LindowsCD 4.0.471 and with LinspireLiveCD 4.5.453;
both of them seem to have the "same" dial-up tool as is on the KnoppixCD 3.4.).
Here's what I get when I "Query Modem" in the Kppp dial-up tool in Lindows:
Lindows Query Modem Results:
ATI: 56000
ATI1: Smart Link 56K Voice Modem unknown Version 2.7.14
ATI2: Smart Link Ltd Version 2.7.14
ATI3: unknown Smart Link compatible modem
ATI4: Active Profile [copied/pasted **see below]
ATI5: Stored Profile 0: Not defined
ATI6: Stored Profile 1: Not defined
ATI7: Serial Number: 0 Protocol Factor: 0
**
Active Profile: S00=000 S01=000 S02=043 S03=013 S04=010 S05=008 S06=002
S07=060 S08=002 S09=006 S10=128 S11=100 S12=050 S13=000 S14=001 S15=001
S16=001 S17=000 S18=000 S19=000 S20=000 S21=000 S22=000 S23=000 S24=050
S25=000 S26=000 S27=008 S28=000 S29
Here are console results:
result about modem from lspci (when on LindowsCD)
00:14.0 Modem: Smart Link Ltd.: Unknown device 3052 (rev 03)
result about modem from lspci -n (when on LindowsCD)
00:14.0 Class 0703: 163c:3052 (rev 03)
result about modem from lspci -v (when on LindowsCD)
00:14.0 Modem: Smart Link Ltd.: Unknown device 3052 (rev 03) (prog-if 00 [Generic])
Subsystem: Unknown device 1688:0811
Flags: bus master, stepping, medium devsel, latency 32, IRQ 10
Memory at eb001000 (32-bit, non-prefetchable) [size=4K]
I/O ports at ec00 [size=256]
Capabilities: [80] Power Management version 2
Any ideas will be greatly appreciated...Thanks!
Knoppix does not include Smartlink modem drivers. You can build your own on a Hd-install, but some knowledge is needed. Some knoppix variants include many extra drivers, maybe look into one of them.
Thank you, kelmo, for your help.
Do you have a suggestion about _where_ I might go to check which Knoppix* variants might include SmartLink modem drivers?
[and/or, other "live CDs"]
Many thanks...
Thanks again...I have posted at Kanotix (en) forum...(after having studied the site as well as a newbie can).Originally Posted by kelmo
We'll wait and see if there are any replies...
wsg, I installed Knoppix v3.4 r2004-05-10 on my system back on the weekend.
I ran into the same problem you had.
The problem is that KPPP is trying to access the modem, and not the PORT the modem is hooked up to.
KPPP -> Configure button -> Device tab -> Modem Device drop down list.
There, select the com port the modem is hooked up to.
Then on the Modem tab, click Querry Modem.
It should now find the modem.
Jenifur Charne
Thanks, Jenifur.
I did go through that procedure, and I think I tried every one of the ports listed in the drop-down menu...to no avail.
But, I think I'll go back and try it again the next time I boot the Knoppix CD.
Regards...
Kelmo...
Among the packages included in the Kanotix list of software, I see these two entries:
sl-modem-daemon2.9.8-1932kSmartLink software modem daemon
sl-modem-modules-2.6.6-kanotix-32.9.8-1+10.00.Custom530kSmart Link modem modules for Linux (kernel 2.6.6-kanotix-3)
Do you have any idea if they would help with my system?
Thanks & Regards...
wsg,
I really meant to suggest that you should install Kanotix instead of knoppix.
Indeed the packages that are included in it are for your modem, but the drivers must be built for the very system you are running, so you cannot just get precompiled binaries from elsewhere and expect them to work for you.
Well, kelmo, as you can see from my lengthy post on the Kanotix Forum (english - general) my system is one wiith no hard drive, so I can't install anything -- just boot and operate from CD.
So, even if I had the Kanotix CD, I would still need to go in search of a modem DRIVER specific for my system, and it would still have to be somehow inserted into the CD** itself. (Don't even know if that's possible.)
**OR, would it have to be on the motherboard - OR...???
Who, among all the developers/venders involved in designing systems, would be the ones who "BUILD DRIVERS" for specific systems?
Thanks again for your help...
1TB/2TB USB 3.0 Flash Drive Thumb U Disk Memory Stick Pen PC Laptop Storage lot
$80.39
1TB HDD/SSD 2.5" SATA Hard Drive for Laptop with Win 10/Win 11 Pro Pre-installed
$28.99
Type C USB 3.0 Flash Drive Thumb Drive Memory Stick for PC Laptop 1TB 2TB lot
$73.29
Samsung 870 EVO EQV 2.5" SATA III Internal SSD - Choose from 1TB 2TB Capacities
$59.00
CISCO A03-D1TBSATA 1TB 7.2K 6G 2.5INCH SATA HDD
$9.95
1TB Samsung 850 Pro Series 2.5" SATA 3 SSD MZ-7KE1T0BW HDD hard drive MZ-7KE1T0
$59.99
Samsung - Geek Squad Certified Refurbished 870 EVO 1TB SATA Solid State Drive
$67.99
Patriot P210 128GB 256GB 512GB 1TB 2TB 2.5" SATA 3 6GB/s Internal SSD PC/MAC Lot
$13.99
1TB HDD/SSD 2.5" SATA Laptop Hard Drive with Win 10/Win 11 Home Pre-installed
$28.99
Samsung 1TB PCIe SSD Drive SSUBX 655-1860H APPLE MacBook Pro A1398 2013-2015
$129.00