If you're not using firewire , then you can disable it by using cheatcode:
nofirewire
You can append this in your /etc/lilo.cfg
Don't forget to update your lilo configuration afterwards: lilo -v
Reboot and run netcardconfig.
After having done a harddisk install of Knoppix 3.6 I find that the system gets confused over my network card. I think it is due to the fact that I have a Firewire card in which it thinks is also a network card. Hence instead of justing staring eth0 it also starts eth1. The interesting thing is that they are not always asigned to the same card...
Hence I have to do a:
ifconfig -a
to find out where the ethernet card really is, then do a:
ifdown eth0 eth1
to stop both, and then do a:
ifup eth0 or eth1 depending on where the ethernet really is...
Strange. How can I prevent this from happening? For your information I include the results of ifconfig -a:
eth0 Link encap:Ethernet HWaddr 00:C0:A8:8D:2A:76
inet addr:62.204.207.16 Bcast:62.204.207.16 Mask:255.255.255.128
inet6 addr: fe80::2c0:a8ff:fe8d:2a76/64 Scope:Link
IPX/Ethernet 802.2 addr:922333C3:00C0A88D2A76
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:39564 errors:0 dropped:0 overruns:0 frame:0
TX packets:15115 errors:0 dropped:0 overruns:0 carrier:0
collisions:4633 txqueuelen:1000
RX bytes:18989122 (18.1 MiB) TX bytes:3603145 (3.4 MiB)
Interrupt:21 Base address:0x9c00
eth1 Link encap:UNSPEC HWaddr 00-30-BD-0B-00-00-15-C8-00-00-00-00-00-00-00-00
inet addr:62.204.207.16 Bcast:62.204.207.16 Mask:255.255.255.128
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:55 errors:1 dropped:1 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:3492 (3.4 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:26254 errors:0 dropped:0 overruns:0 frame:0
TX packets:26254 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4061191 (3.8 MiB) TX bytes:4061191 (3.8 MiB)
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Thanks,
Tim
If you're not using firewire , then you can disable it by using cheatcode:
nofirewire
You can append this in your /etc/lilo.cfg
Don't forget to update your lilo configuration afterwards: lilo -v
Reboot and run netcardconfig.
Thanks, but I am using Firewire for an external 200GB hard disk...
And regarding putting the other commands in lilo, that would not work becuase I have to manually see wheter eth0 or eth1 has been associated with the Ethernet before using if up...
Tim
***NEW*** BCM RX67Q Gaming Motherboard | Intel Q67 2nd/3rd Gen. | LGA1155 | DDR3
$29.77
ASUS H110M-R Motherboard Intel 6th/7th Gen LGA1151 DDR4 Micro-ATX i/o shield
$42.00
Micro ATX Desktop Motherboard ASUS H110M-C LGA 1151
$31.95
MSI A320M-A PRO AM4 AMD A320 USB3.2 Gen1 Micro-ATX Motherboard
$46.99
Gigabyte AMD B550 UD AC Gaming Motherboard - AMD B550 Chipset - AM4 Socket - AMD
$89.99
ASUS Prime Z390-A LGA 1151 Intel Z390 SATA USB 3.1 ATX Motherboard NO I/O
$99.00
Gigabyte GA-B75M-HD3 Intel LGA1155 DDR3 Desktop Motherboard MicroATX USB 3.0
$26.99
ASUS Prime Q270M-C LGA1151 DP HDMI VGA SATA 6GB/s USB 3.0 MicroATX Motherboard
$37.99
BTC-S37 Mining Motherboard Kit /w SSD & Ram Preinstalled
$59.99
MSI B550M PRO-VDH WIFI Socket AM4 AMD Motherboard
$80.00