-
Senior Member
registered user
Network works...then it doesn't
Weird problem just started with my Toshiba laptop/Netgear pcmcia ethernet card.
It sets up properly & broadcasts for DHCP as part of knoppix-autoconfig script. Then it trashes the pcmcia connection.
Startup messages look some thing like this:
modprobe 8390
modprobe pcnet_cs
./network start eth0
/sbin/ifconfig eth0 up
/sbin/pump -i eth0 > dev/null
All this is as part of knoppix-autoconfig script; I have inserted an 'end of autoconfig script' echo command to aid troubleshooting so I can tell when it exits.
Then, immediately following the autoconfig script, it does the following:
[re]starting pcmcia services (in green)
cardmgr [109] ./network check eth0
cardmgr [109] ./network stop eth0
cardmgr [109] /sbin/pump -r -i eth0
cardmgr [109] modprobe -r pcnet_cs
cardmgr [109] modprobe -r 8390
cardmgr [109] exiting
cardmgr [505] error in file 'config line 2288 unknown device prism_cs
cardmgr [505] open_sock (socket 0) failed device or resource busy
Then it goes on to start cups & samba & startx. At this point I have no net connection. I have checked this by inserting a 'ping' test command at the end of knoppix-autoconfig & again at the start of /etc/init.d/xsession. First ping is OK, second fails.
I doubt if anybody else has actually had this problem, I always seem to get the weird ones, but can anybody help?
Why would this suddenly start doing this? Why/what script is attempting to [re]start pcmcia services & screwing it up. (Note: running from CD it appears not to do this) What controls the startup procedure...what calls knoppix-autoconfig & what is supposed to happen next?
-
Senior Member
registered user
I have partially solved this but still have questions.
Tracking through the startup procedure, knoppix-autoconfig runs first. It correctly identifies & sets up the PCMCIA ethernet card on socket 1. Then knoppix-hd-config runs. It attempts to restart the ethernet card (why??). It succeeds in shutting down the card, removing modules (modprobe -r) pcnet_cs & 8390 but then fails attempting to restart because it finds an open socket (socket 0) which it is unable to close.
I have done a 'workaround' disabling the shutdown part of the process, network now stays up but can somebody explain why knoppix-hd-config wants to do the shutdown/restart in the first place & how do I figure out what socket 0 is doing.
Similar Threads
-
By Silvix in forum Networking
Replies: 0
Last Post: 06-02-2005, 04:02 AM
-
By kpf8655 in forum Hdd Install / Debian / Apt
Replies: 7
Last Post: 07-02-2004, 01:13 PM
-
By Corwin in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 04-04-2004, 03:29 AM
-
By BluntMan in forum Networking
Replies: 0
Last Post: 11-17-2003, 01:28 AM
-
By Mokoshi in forum Networking
Replies: 1
Last Post: 10-07-2003, 03:04 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
AUDIO CODES MP-114 VOIP Gateway Open Box
$37.49
Polycom VVX 450 Business IP Phone - VoIP phone P/N: 2200-48840-025
$49.99
Cisco IP phone 7945
$7.99
Yealink W56H Handset
$157.36
Cisco CP-7945G VOIP Phone With Stand & Handset Business IP Phone 7945
$3.00
New Cisco 7945G IP VoIP Gigabit GIGE Telephone Phone CP-7945G -
$24.95
Yealink SIP-T41P PoE Ultra Elegant VoIP Phone
$29.95
Cisco CP-8845-K9 5 Line IP Video Phone - Charcoal
$25.00
Grandstream GS-HT802 2 Port Analog Telephone Adapter VoIP Phone & Device, Black
$32.00
Cisco 8841 CP-8841-K9 VoIP Business IP Phone (Charcoal)
$49.00