-
Senior Member
registered user
More DD to an image
Ok, I'm looking at your dd to an image.
I want to try doing that to a different partition on my Windows XP drive.
I'm thinking if I totally defrag the partition first in XP and back it up first I should be OK to try it.
sakiZ
-
Senior Member
registered user
Re: More DD to an image
Originally Posted by
sakiZ
Ok, I'm looking at your dd to an image.
I want to try doing that to a different partition on my Windows XP drive.
I'm thinking if I totally defrag the partition first in XP and back it up first I should be OK to try it.
If the partition you want to write the image on is an ntfs formatted partition then I wouldn't bother trying to do it under Linux, either you will have to use paragons ntfs drivers (which I gather are reasonable), or use captive-ntfs which is horribly horribly slow or use linux's normal ntfs tools which means you'ld probably have to figure out what size the file would be (exactly) first, then allocate a file that size in windows on the ntfs drive and finally go into Knoppix and do your dd (hoping it comes out the same size), this is because with normal ntfs write support on Linux you can only write to files without changing the filesize and it can't add/remove files or folders!
If it is a fat partition or some Linux type then it shouldn't be a problem (whether you defrag it or not, but it probably only makes sense to defrag it if it is a fat partition, the default from dos and Windows 9x).
-
Senior Member
registered user
Cloned It AND Loop Mounted IT!!!!
Hey Bfree,
Thanks to you I tried your "dd" trick and it worked!!!
I defragged my partition to recieve the image file, scanned it for errors and backed it up, all in Windows XP.
I booted into Knoppix and did the "dd" command you gave me to create the hdb2.img file.
So far so good.
Next I followed your second step and created the loop mount. Well, I'll be!!! There is my image file appearing as a mirrored clone in my root directory!!!! Amazing.
So to make a clone I do:
"dd if=/mnt/hda6/hdb2.img /dev/hdb2"
If this were to be a clone of my Knoppix set up on a NEW drive would the command then actually be:
"dd if=/mnt/hda6/hdb2.img /dev/had1" ???
Thanks so much for your help.
Windows could never do anything like this.
sakiZ
-
Senior Member
registered user
Re: Cloned It AND Loop Mounted IT!!!!
Originally Posted by
sakiZ
So to make a clone I do:
"dd if=/mnt/hda6/hdb2.img /dev/hdb2"
If this were to be a clone of my Knoppix set up on a NEW drive would the command then actually be:
"dd if=/mnt/hda6/hdb2.img /dev/had1" ???
Not quite. To restore/clone the image into a partition do
Code:
dd if=/mnt/hda6/hdb2.img of=/dev/hdb2"
If you were putting it onto a new drive you would again use the of=. Aswell as that you would proably have to use a rescue disk to tweak the system (fix the bootloader and /etc/fstab) before you could boot it. If it's windows on the other hard I'm not sure what you can do apart from restore it to the same position on a new drive with the same partition table as the original device (you can backup the masterboot record and partition table of your drive with "dd if=/dev/hda of=hda-start bs=512 count=1" and restore it with the reverse) which I'm 99% certain will be ok.
Just to point out one last trick, you can dd an entire disk device, e.g. "dd if=/dev/hda of=hda.img" and "dd if=hda.img of=hdb" but mounting the images from within these requires you to use some tricks to give an offset argument to mount. Here's instructions.
Similar Threads
-
By Jakykong in forum The Lounge
Replies: 2
Last Post: 12-14-2005, 08:36 AM
-
By Cuddles in forum General Support
Replies: 9
Last Post: 11-26-2004, 10:57 PM
-
By helios17 in forum General Support
Replies: 12
Last Post: 10-28-2004, 12:47 PM
-
By Jaguar600 in forum General Support
Replies: 5
Last Post: 09-27-2004, 10:34 PM
-
By mconzo in forum MS Windows & New to Linux
Replies: 4
Last Post: 09-06-2004, 02:09 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Dell PowerEdge R720 Server - 2x8c CPU,256Gb RAM, 128Gb SSD/3x900Gb SAS, Proxmox
$340.00
DELL PowerEdge R730 Server 2x E5-2690v3 2.6GHz =24 Cores 32GB H730 4xRJ45
$274.00
Dell PowerEdge R720XD Xeon E5-2680 V2 2.8GHz 20 Cores 256GB RAM 12x4TB
$510.00
Dell PowerEdge R620 Server 2x E5-2660 v1 2.2GHz 16 Cores 256GB RAM 2x 300GB HDD
$79.19
Dell PowerEdge R730XD 28 Core Server 2X Xeon E5-2680 V4 H730 128GB RAM No HDD
$389.99
Dell Emc R750 Computer Poweredge edge racked server.
$750.00
Dell PowerEdge R730, 2 sinks, SystemBoard, 8 trays,H330,Idrac 8 exp, 2x750w Psu
$135.00
Dell PowerEdge R730 Server 2x E5-2670v3 2.30Ghz 24-Core 128GB H730
$411.75
Dell PowerEdge R720 Server | 2x E5-2660 2.2GHz | 128GB Ram | 1.2TB HDD | H710P
$179.00
DELL PowerEdge R630 8SFF Server 2x E5-2680v3 2.5GHz =24 Cores 128GB H730 4xRJ45
$360.00