Hello..
Forgot to add that I was trying to install Knoppix 3.7 !
Hi all,
I just burned a knoppix live CD and was booting with the CD.
I got the below message and wasnt able to boot complete with KDE .. The CD works fine in another computer.
Welcome to the KNOPPIX live Linux-on-CD!
Scanning for USB/Firewire devices... Done.
Enabling DMA acceleration for: hda [xxxxxxxxx]
Enabling DMA acceleration for: hdc [yyyyyyyyy]
Looking for CDROM in: /dev/scd0
Can't find KNOPPIX filesystem, sorry.
Dropping you to a (very limited) shell.
Press reset button to quit.
additional builtin commands avaliable:
cat mount umount
insmod rmmod lsmod
knoppix#
Then , i tried booting using the FAILSAFE mode ..with which i booted sucessfully . I then ran "sudo knoppix installer" ..the partition manager ran and i created partitions of a swap size of 300 MB and an EXT3 parition of 4.7GB . After this, the installation program is terminated and im back in the LInux kDE again.
I dont understand why this is happening and what are the suggested techniques i can use to install knoppix.
I had installed knoppix 3.3 in the past and it worked perfectly. the command knx-hdinstall doesnt work at root !!
My system configuration:
P II 400 Mhz, 128 MB ram , 48 X cd drive , 13gb + 9 gb Hdd's , INTEL 440 BX motherboard.
currently running windows 2000.
Any help would be appreciated.
Thanks in advance.
Hello..
Forgot to add that I was trying to install Knoppix 3.7 !
If it will boot failsafe it probably means that it is not detecting some hardware correctly...probably your video card. Try cheatcodes to solve this.
What happens if you boot failsafe then 'startx' or 'kdm'? Does the gui start?
They is/was a bug in the knoppix installer which stops it from running from terminal; kanotix has fixed this but I don't know if kanotix-installer can be used to install knoppix. So you may have to get KDE working in order to HD install.
KDE is working when i start with failsafe. i found that some users had the same problem as im facing that the cd doesnt load LINUX on normal startup
I have to start it in failsafe mode and then the installer is buggy in the failsafe mode.
any linux gurus tell me whats wrong???????
Try boot with cheatcode : nodma or noscsi
Sounds like you used the right technique to burn the CD.Originally Posted by squireofgothos
Did you confirm the md5 checksum of the iso before you burnt it?
Did you burn at a nice reasonable speed like 4x rather than telling the CD writer to go like a bat out of hell? This error sounds very much like the CD drive is having a lot of trouble reading the CD. Is the CD drive in good shape, or have you had other problems with it? (And I do agree with shah's cheat codes, particularly nodma).
Hi,
what about the problem with the installer ??? when i run the command, sud knoppix-installer ,
the installer exits just after the partioning is done...
any ideas??
booting with the cheat code NODMA worked !
I usually have the following on my system
hda1 (windows C)
hda2 (/boot)
hda4 (extended)
hda5 (windows D)
hda6 (windows E)
hda7 (windows F)
hda8 (/)
hda9 (swap)
I do this, because in the past, lilo required to be below the 1024 cylinder boundery. Nowadays I'm using grub, which doesn't have the problem, but it is installed on the /boot partition anyways.
The ultimate advantage of ths setup is, that I set /dev/hda2 active and can use gub to boot linux or windows. If I damange my linux (like now) I can still use grub to boot windows.
If I decide (like now) to reformat /dev/hda2 and start over again, I simply set /dev/hda1 active and Windows can boot by itself again, since nothing was modified.
Now I want to install Knoppix 3.7 to the HDD and want to use:
1) GRUB insteat lilo
2) Place grub in /dev/hda2 and not in /dev/hda8 like the installer does it.
I manually changed the config file before I did the install. But for option (2) I don't have any glue that doing it per hand myself, when the install is finished.
Sincerly, Art
Hello,
can anybody answer my question ?
the install quits after i do the partioning saying that the filesystem is larger than drive
i posted the question . got 77 views but no Replies !!!
can anyone tell me why im getting the error during installation??
my partions are clean on my hdd..
Thanks
Dell PowerEdge R7525 Server 24X2.5(8XNVME)+H745 2xEPYC 7302 CPU 128G RAM 2x2400W
$3350.00
DELL PowerEdge R730 Server 2x E5-2690v3 2.6GHz =24 Cores 32GB H730 4xRJ45
$274.00
Dell PowerEdge R720XD Xeon E5-2680 V2 2.8GHz 20 Cores 256GB RAM 12x4TB
$510.00
Dell PowerEdge R730, 2 sinks, SystemBoard, 8 trays,H330,Idrac 8 exp, 2x750w Psu
$135.00
Dell PowerEdge R730XD 28 Core Server 2X Xeon E5-2680 V4 H730 128GB RAM No HDD
$389.99
Dell PowerEdge R620 Server 2x E5-2660 v1 2.2GHz 16 Cores 256GB RAM 1x 300GB HDD
$89.99
Dell PowerEdge R720 Server - 2x8c CPU,256Gb RAM, 128Gb SSD/3x600Gb SAS, Proxmox
$340.00
DELL PowerEdge R730 16SFF Server 2x E5-2690v4 =28 Cores No RAM/ HDD H730 4xRJ45
$232.97
DELL PowerEdge R630 8SFF Server 2x E5-2690v3 2.6GHz =24 Cores 32GB H730 4xRJ45
$254.00
Dell R630 8 Port SFF Server 2x E5-2680v4 28C H730P 128GB 2x Trays RJ-45 ENT
$345.00