-
Junior Member
registered user
I was able to solve the usb mouse detection problem by installing knoppix on my hard disk, set up gpm with the following configuration options: <gpm.conf>
device=/dev/input/mice
responsiveness=
repeat_type=raw
type=autops2
append=""
sample_rate=
</gpm.conf>, and by changing the XF86Config-4 file in the sections <ServerLayout> InputDevice "USB Mouse" "CorePointer"
</ServerLayout> and adding a new <Section "InputDevice">
Section "InputDevice"
Identifier "USB Mouse"
Driver "mouse"
Option "Device" "/dev/gpmdata"
Option "SendCoreEvents" "true"
Option "Protocol" "auto"
Option "ZAxisMapping" "4 5"
Option "Buttons" "5"
EndSection
<Section "InputDevice">.
I have also automated this procedure adding a few symbolic links:
/etc/rc0.d/K20gpm -> ../init.d/gpm
/etc/rc1.d/K20gpm -> ../init.d/gpm
/etc/rc2.d/S20gpm -> ../init.d/gpm
/etc/rc3.d/S20gpm -> ../init.d/gpm
/etc/rc4.d/S20gpm -> ../init.d/gpm
/etc/rc5.d/K20gpm -> ../init.d/gpm
/etc/rc5.d/S20gpm -> ../init.d/gpm
/etc/rc6.d/K20gpm -> ../init.d/gpm
cu, g.
-
FLASH CARD READER MSC USB (something)
I am a newbie and i have problems with Knoppix installed in my hdard drive, how can i install a driver for this USB card reader, and i canīt work either with mzip tools it doesnīt detecth my paralell Zip drive, some times at boot it gets frozens. Thank you for your help...
-
Senior Member
registered user
Originally Posted by
dmiller
for my hp psc2210 I had to download and install hpijs from the hp website. This was the essential piece of glue to get the HP printer to work under knoppix. comes with instructions for how to install in linux and check if it is working....
Summary,
suggest searcing the HP site for HPIJS .
I searched but found nothing in HP site and still unable to print with my psc2210.
Any links or suggestions?
-
Problem: Autoconfiguration Hangs endlessly on boot with Knoppix 3.9
Solved by: knoppix nousb (at boot)
Suspect: Newer PCI Express specification not recognized
Computer: Fujitsu N3511 laptop ( Brand New )
Question:
How can you manually load the USB drivers 'after' a 'knoppix nousb' boot option?
Question 2:
Has anyone gotten knoppix 3.9 running with a PCI Express featured system?
I was surprised to learn that the new PCI express spec also applies to the USB bus...
maybe this is a factor in Knoppix 3.9 failure to detect the USB properly???
I don't know if this applies, but here below are the results from a lspci:
root@0[knoppix]# lspci | grep -i usb
0000:00:1d.0 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 04)
0000:00:1d.1 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 04)
0000:00:1d.2 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 04)
0000:00:1d.3 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 04)
0000:00:1d.7 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 04)
root@0[knoppix]# lspci -vv -s 00:1d.0
0000:00:1d.0 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 04) (prog-if 00 [UHCI])
Subsystem: Fujitsu Limited.: Unknown device 12e8
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 4: I/O ports at 1200 [size=32]
Similar Threads
-
By obsoleto in forum Hardware & Booting
Replies: 1
Last Post: 06-04-2004, 05:11 PM
-
By jcostello in forum Hardware & Booting
Replies: 1
Last Post: 04-24-2004, 01:33 AM
-
By Danmak in forum Hardware & Booting
Replies: 3
Last Post: 12-01-2003, 03:40 AM
-
By staverts in forum Hardware & Booting
Replies: 0
Last Post: 07-28-2003, 06:48 AM
-
By Christer in forum Hdd Install / Debian / Apt
Replies: 1
Last Post: 04-02-2003, 03:32 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Dell PowerEdge R720 Server - 2x8c CPU,256Gb RAM, 128Gb SSD/3x900Gb SAS, Proxmox
$340.00
Dell PowerEdge R620 Server 2x E5-2660 v1 2.2GHz 16 Cores 256GB RAM 2x 300GB HDD
$89.99
Dell PowerEdge R730XD 28 Core Server 2X Xeon E5-2680 V4 H730 128GB RAM No HDD
$389.99
Dell Poweredge XC730xd 3.5 2x E5-2690 v3 2.6ghz 64gb JBOD 12x Trays 2x1100w
$239.99
CTO Dell PowerEdge R630 Server, 2x Xeon E5-2620V4, 64GB- 512GB RAM, 480GB SSDs
$246.67
DELL POWEREDGE T430 SERVER W/ DUAL XEON E5-2609 CPU & 16GB MEMORY
$329.00
Dell R730 8B LFF 2x 2.40GHz 14C Intel Xeon E5-2680 v4 32GB RAM 2x 3TB HDD HBA330
$299.99
Dell Poweredge R620 8-Bay CTO Pick your CPU & RAM Config | H710 Raid | 2x PSU
$209.99
DELL PowerEdge R730 Server 2x E5-2680v4 2.4GHz =28 Cores 32GB H730 4xRJ45
$284.00
Dell Poweredge R640 8 SFF Server No HDDs/ CPUs/ RAMs/ Cards/Fan/PSU
$419.99