-
Junior Member
registered user
Knoppix won't boot after HD install
All right, I have a new problem. I've installed knoppix to my HD, but I can't get it to boot. It shows the NT bootloader and XP boots, but I can't see any sign of knoppix. I used the knoppix 3.7 installer and selected for lilo to be installed in MBR. Any advice would be greatly appreciated.
-
Junior Member
registered user
Right. I looked in cfdisk and noticed that my windows partition was marked as bootable, my linux partition wasn't. Sould I just mark my linux partition as bootable? That may seem like a stupid question, but I don't know what I'm doing and don't want to screw anything up. Again, thanks for any help you can provide.
-
Senior Member
registered user
Originally Posted by
ixalarx
Right. I looked in cfdisk and noticed that my windows partition was marked as bootable, my linux partition wasn't. Sould I just mark my linux partition as bootable? That may seem like a stupid question, but I don't know what I'm doing and don't want to screw anything up. Again, thanks for any help you can provide.
No, you don't want your linux partition set to bootable, lilo will boot it. It sounds like lilo did not install properly if the first screen you see is XP booting. Boot into your HD install from the CD with 'knoppix lang=us root=/dev/hda5 noinitrd ro' (replace hda5 with the correct partition for your install). Then check /etc/lilo.conf to see if it is correct. It should have 'boot=/dev/hda', an entry for knoppix and an entry for windows. Then open a console & 'sudo lilo' to try to install lilo from the HD install. Follow up on any error messages.
One of the bugs in the hdinstaller is that if something goes wrong with the lilo install it doesn't report back to the user, it just continues on without installing lilo. One potential source of trouble is that the installer adds any cheatcodes in effect to the 'append=' line in lilo.conf & lilo sometimes doesn't like things repeated...like for instance if you are using the cheatcode 'vga=normal' this will conflict with the 'vga=791' which is part of the default lilo.conf.
-
Junior Member
registered user
Okay, I checked the file and it looks fine, but when I ran lilo at the command line I got this output:
/dev/mapper/control: open failed: No such device
Is device-mapper driver missing from kernel?
/dev/mapper/control: open failed: No such device
Is device-mapper driver missing from kernel?
Incompatible libdevmapper 1.00.19-ioctl (2004-07-03)(compat) and kernel driver
Warning: Unable to determine video adapter in use in the present system.
Added Linux *
Added Linux(2.4)-1
Added Linux(2.6)-2
Warning: CHANGE AUTOMATIC assumed after "other=/dev/hda2"
Device 0x0300: Inconsistent partition table, 2nd entry
CHS address in PT: 619:0:1 --> LBA (9944235)
LBA address in PT: 9359280 --> CHS (582:150:1)
Fatal: Either FIX-TABLE or IGNORE-TABLE must be specified
If not sure, first try IGNORE-TABLE (-P ignore)
I have no clue what this means, but I hope it helps.
-
If not sure, first try IGNORE-TABLE (-P ignore)
lilo -P ignor
and reboot
-
Junior Member
registered user
I would have tried the lilo -P thing, but now when trying to boot from HD with the CD it doesn't start at all. It gets to
"Running from HD, regenerate ld.so.cache and modules.dep..." then stops. The light on the case shows no HD activity. Am i pretty much screwed here?
-
what do u get on boot is lilo now or still xp
sorry have to leave
-
Junior Member
registered user
No, I'm using the CD to boot from the HD.
-
using the CD to boot from the HD.
how
fromhd
or
whith chroot
and if you boot from your hd what's happend
see your tomorrow
-
Junior Member
registered user
Sorry, I was pretty rushed and couldn't post very coherently. I'll just recap what happened. After reading your post about using lilo -P, I tried to boot using Crashed's instructions "knoppix lang=us root=/dev/hda5 noinitrd ro", but the booting seemed to stop after showing "Running from HD, regenerate ld.so.cache and modules.dep..." It still does not show anything while booting without the CD but the NT bootloader.
Similar Threads
-
By AlphaBluesMan in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 02-24-2006, 10:44 AM
-
By AgustinCordoba in forum Hdd Install / Debian / Apt
Replies: 5
Last Post: 09-20-2005, 04:43 PM
-
By bigrobot in forum Networking
Replies: 0
Last Post: 12-06-2004, 02:32 PM
-
By ku in forum General Support
Replies: 1
Last Post: 03-17-2004, 11:41 PM
-
By orvil in forum Hdd Install / Debian / Apt
Replies: 5
Last Post: 05-29-2003, 02:09 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Dell PowerEdge R720 Server - 2x8c CPU,256Gb RAM, 128Gb SSD/3x900Gb SAS, Proxmox
$340.00
Dell PowerEdge R620 Server 2x E5-2660 v1 2.2GHz 16 Cores 256GB RAM 2x 300GB HDD
$89.99
Dell PowerEdge R730XD 28 Core Server 2X Xeon E5-2680 V4 H730 128GB RAM No HDD
$389.99
Dell Poweredge XC730xd 3.5 2x E5-2690 v3 2.6ghz 64gb JBOD 12x Trays 2x1100w
$239.99
CTO Dell PowerEdge R630 Server, 2x Xeon E5-2620V4, 64GB- 512GB RAM, 480GB SSDs
$246.67
DELL POWEREDGE T430 SERVER W/ DUAL XEON E5-2609 CPU & 16GB MEMORY
$329.00
Dell R730 8B LFF 2x 2.40GHz 14C Intel Xeon E5-2680 v4 32GB RAM 2x 3TB HDD HBA330
$299.99
Dell Poweredge R620 8-Bay CTO Pick your CPU & RAM Config | H710 Raid | 2x PSU
$209.99
DELL PowerEdge R730 Server 2x E5-2680v4 2.4GHz =28 Cores 32GB H730 4xRJ45
$284.00
Dell Poweredge R640 8 SFF Server No HDDs/ CPUs/ RAMs/ Cards/Fan/PSU
$419.99