-
Junior Member
registered user
Knoppix won't boot after HD install
All right, I have a new problem. I've installed knoppix to my HD, but I can't get it to boot. It shows the NT bootloader and XP boots, but I can't see any sign of knoppix. I used the knoppix 3.7 installer and selected for lilo to be installed in MBR. Any advice would be greatly appreciated.
-
Junior Member
registered user
Right. I looked in cfdisk and noticed that my windows partition was marked as bootable, my linux partition wasn't. Sould I just mark my linux partition as bootable? That may seem like a stupid question, but I don't know what I'm doing and don't want to screw anything up. Again, thanks for any help you can provide.
-
Senior Member
registered user
Originally Posted by
ixalarx
Right. I looked in cfdisk and noticed that my windows partition was marked as bootable, my linux partition wasn't. Sould I just mark my linux partition as bootable? That may seem like a stupid question, but I don't know what I'm doing and don't want to screw anything up. Again, thanks for any help you can provide.
No, you don't want your linux partition set to bootable, lilo will boot it. It sounds like lilo did not install properly if the first screen you see is XP booting. Boot into your HD install from the CD with 'knoppix lang=us root=/dev/hda5 noinitrd ro' (replace hda5 with the correct partition for your install). Then check /etc/lilo.conf to see if it is correct. It should have 'boot=/dev/hda', an entry for knoppix and an entry for windows. Then open a console & 'sudo lilo' to try to install lilo from the HD install. Follow up on any error messages.
One of the bugs in the hdinstaller is that if something goes wrong with the lilo install it doesn't report back to the user, it just continues on without installing lilo. One potential source of trouble is that the installer adds any cheatcodes in effect to the 'append=' line in lilo.conf & lilo sometimes doesn't like things repeated...like for instance if you are using the cheatcode 'vga=normal' this will conflict with the 'vga=791' which is part of the default lilo.conf.
-
Junior Member
registered user
Okay, I checked the file and it looks fine, but when I ran lilo at the command line I got this output:
/dev/mapper/control: open failed: No such device
Is device-mapper driver missing from kernel?
/dev/mapper/control: open failed: No such device
Is device-mapper driver missing from kernel?
Incompatible libdevmapper 1.00.19-ioctl (2004-07-03)(compat) and kernel driver
Warning: Unable to determine video adapter in use in the present system.
Added Linux *
Added Linux(2.4)-1
Added Linux(2.6)-2
Warning: CHANGE AUTOMATIC assumed after "other=/dev/hda2"
Device 0x0300: Inconsistent partition table, 2nd entry
CHS address in PT: 619:0:1 --> LBA (9944235)
LBA address in PT: 9359280 --> CHS (582:150:1)
Fatal: Either FIX-TABLE or IGNORE-TABLE must be specified
If not sure, first try IGNORE-TABLE (-P ignore)
I have no clue what this means, but I hope it helps.
-
If not sure, first try IGNORE-TABLE (-P ignore)
lilo -P ignor
and reboot
-
Junior Member
registered user
I would have tried the lilo -P thing, but now when trying to boot from HD with the CD it doesn't start at all. It gets to
"Running from HD, regenerate ld.so.cache and modules.dep..." then stops. The light on the case shows no HD activity. Am i pretty much screwed here?
-
what do u get on boot is lilo now or still xp
sorry have to leave
-
Junior Member
registered user
No, I'm using the CD to boot from the HD.
-
using the CD to boot from the HD.
how
fromhd
or
whith chroot
and if you boot from your hd what's happend
see your tomorrow
-
Junior Member
registered user
Sorry, I was pretty rushed and couldn't post very coherently. I'll just recap what happened. After reading your post about using lilo -P, I tried to boot using Crashed's instructions "knoppix lang=us root=/dev/hda5 noinitrd ro", but the booting seemed to stop after showing "Running from HD, regenerate ld.so.cache and modules.dep..." It still does not show anything while booting without the CD but the NT bootloader.
Similar Threads
-
By AlphaBluesMan in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 02-24-2006, 10:44 AM
-
By AgustinCordoba in forum Hdd Install / Debian / Apt
Replies: 5
Last Post: 09-20-2005, 04:43 PM
-
By bigrobot in forum Networking
Replies: 0
Last Post: 12-06-2004, 02:32 PM
-
By ku in forum General Support
Replies: 1
Last Post: 03-17-2004, 11:41 PM
-
By orvil in forum Hdd Install / Debian / Apt
Replies: 5
Last Post: 05-29-2003, 02:09 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Fortinet FortiGate 60F | 10 Gbps Firewall Network Security EXPIRED (FG-60F)- New
$226.79
Palo Alto PA-220 Next Generation Firewall Appliance w/ Power Adapter and Cord
$62.99
1U BareMetal pfsense opnsense Router Firewall DNS Server 6x 10GB Ethernet Ports
$149.00
Fortinet FortiGate 100D Next Generation Firewall (FG-100D)
$45.00
Cisco Meraki MX84 Cloud Managed Security Firewall Appliance UNCLAIMED MX84-HW
$39.99
Cisco ASA5506-K9 ASA 5506-X Network Security Firewall
$40.00
Dell SonicWall TZ300 5 Port Network Security Firewall Appliance APL28-0B4
$39.99
Fortinet Fortigate-60E Network Security Firewall FG-60E Power Cord
$59.00
Fortinet Fortigate FG-61E Firewall Network Security Appliance ATP Bundle 1 years
$263.99
SonicWALL TZ300 Network Security Appl FirewallRouter5pt 01-SSC-0215TransferReady
$45.00