View Poll Results: Anyone have success coexisting with WINDOZE?
- Voters
- 7. You may not vote on this poll
-
yes, but I nuked the WINDOZE partition
-
yes, I had no problem
-
no, I'm scared of repartitioning my HD
-
no, my better half will implode
-
Senior Member
registered user
CoExisting with WINDOZE
OK, before you guys start flaming me, this is my better half's PC with a winmodem! She'll die if I get rid of WINDOZE....
Anyway, I ran knx-hdinstall and managed to kill the WINDOZE partition when trying to make new linux and linux swap partitions with cfdisk.
Question 1: Is there some way to repartition a HD to install KNOPPIX without killing the currently installed WINDOZE (single partition of whole drive)?
Also, I reinstalled everything as follows:
hda1 WIN FAT32 3000KB
hda2 linux swap 256KB
hda3 linux rest of drive.
I reinstalled WINDOZE and had it working before reinstalling KNOPPIX. Now I can't boot into WINDOZE. Only KNOPPIX shows up on the dual boot screen.
Question 2:How do I undo this? Is it an MBR problem? Now I have a great Debian install on the HD, but cannot boot WINDOZE! Should I not have used one of the last knx-hdinstall options for the MBR dual boot? Could I have used a boot disk to boot the Debian install on the HD when I want and just boot to WINDOZE otherwise?
Thanx,
-
Don't panic ...
Don't panic there is a nice solution for this problem:
- Start debian
- Edit /etc/lilo.conf as root (Using vi or joe, or whatever you like)
Add:
other=/dev/hda1
label=Windows
table=/dev/hda
to the end of it ...
Start
lilo
(also as root)
Reboot and boot your Windows by selectiing it from the menu ...
cu
Fabian
-
use "parted" or "nparted" (the later with a simpler interface) to repartition the drive. this works well with FAT partitions, NTFS beeing a problem.
Otherwise use one of the commercial partition mannagers to free some space on the disk.
-
Senior Member
registered user
Is "parted" freeware? I understand that the commercial program partitionmagic works well for this. I'd like to stick to open source or freeware.
Thanx, Fabian, I tried your fix and everything works fine!
Regards,
-
Co-existing with windows
I used Partition Magic 5.0 in Win98 to partition first. No problems on install. Installed knoppix on hda 2 and had it boot from there also. Used Boot Magic as boot manager.
Only problem. I still can't get on the net using any type of linux since I reinstalled windoze. I have to wonder how this is possible.
I think the problem is in the eth0 setup.
Does anyone know how to put eth0 into 10 half duplex mode?
Thanks
Similar Threads
-
By Jameson in forum General Support
Replies: 2
Last Post: 10-22-2004, 06:05 PM
-
By helios17 in forum General Support
Replies: 1
Last Post: 09-30-2004, 01:40 PM
-
By phaedral in forum Hdd Install / Debian / Apt
Replies: 3
Last Post: 09-13-2004, 11:40 PM
-
By duah55 in forum General Support
Replies: 0
Last Post: 02-20-2004, 04:56 PM
-
By shadoman in forum Hdd Install / Debian / Apt
Replies: 8
Last Post: 12-01-2003, 09:13 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Juniper SRX650 VPN Firewall Security Hub SRX650-BASE-SRE6-645AP w/SRX-GP-IM
$99.99
Juniper MX-MPC2-3D-A Router Card + MIC-3D-4XGE-XFP-A & MIC-3D-20GE-SFP
$799.99
Juniper Networks EX3300-48P 48-Port PoE+ 4x SFP+ Network Switch w/ Power Cord
$43.95
Juniper Networks EX4300-48T 48 Port Gigabit 4 QSFP 40G 2xPSU AFO Network Switch
$89.00
JUNIPER EX3400-48P 48x 1GB PoE+ RJ-45 4x 10GB SFP+ 2x 40GB QSFP+, DUAL AC POWER
$210.00
Juniper Networks EX3300 EX3300-48P 48-Port Gigabit PoE+ Switch
$40.10
Juniper QFX5100-48S-3AFO Switch 48 x 10Gb SFP+, 6x QSFP 40GE, Dual AC Power
$499.00
Juniper EX4600-40F-AFI 24 SFP+/SFP Ports 4 QSFP+ Ports Dual AC Switch
$999.00
Juniper PD-4OC192-SON-XFP 710-013264 Four line-rate OC-192c/ STM-64 IPUIA01MTA
$675.00
New Factory Sealed Juniper EX2300-48P Networks 48-Port Managed Ethernet Sealed
$499.00