-
Is there a way to run knoppix from the harddisk with out ...
I want to run knoppix straight from my hd without having to dual boot, I prefer knoppix over windows and would rather not have it on my pc.Is it possible and if so can some one tell me how to do it.<---complete n00b.
Thanks.
-
Senior Member
registered user
For a Knoppix only system, simply wipe your HD, reformat your HD.
I would use three partitions:
One for Knoppix O/S format ext3 about 5 gig
One for swap about 500 meg format linux swap
rest for data format ext3
so that data is on a separate partition from the O/S to protect it in case of an O/S crash.
but you can just use 2...500 meg for swap & rest for Knoppix.
Then just do a Knoppix HD install with the command 'sudo knoppix-installer'.
If you use 3 partitions, once Knoppix is installed you can set up to either move your /home directory to your data partition or else leave /home where it is but put in a symlink to your data partition so that you can easy access it.
-
Senior Member
registered user
You do not need windows on your drive if you don't want it.
I ran that way ( sans win ) for a long time.
You could use qtparted to delete the windows partiton.
I assume you will save any files you want, and then you can
either use the extra space for /home or just add to your root partition.
You could give this link a read: http://pw1.netcom.com/~kmself/Linux/FAQs/partition.html
Once you have the drive formatted the way
you want you can install knoppix. Good luck!
-
Re: Is there a way to run knoppix from the harddisk with out
Originally Posted by
Dobez
I want to run knoppix straight from my hd without having to dual boot, I prefer knoppix over windows and would rather not have it on my pc.Is it possible and if so can some one tell me how to do it.<---complete n00b.
Thanks.
Here's what I did:
-use qtparted to create an ext3 partition for knoppix, and a linux-swap partition for swapping
-run knx2hd to install knoppix
-when asked if I want to install LILO on the MBR or the partition, choose PARTITION
-reboot
-edit my boot sequence in my BIOS to check the CD-ROM drive before checking any hard drives
-boot from the knoppix CD
-at the boot console, type "knoppix root=/dev/sda1 noinitrd ro", so that a) Knoppix will see /dev/sda1 as the hard disk installation to boot up, and b) so that knoppix won't initialise a ram disk and try to run from that
That's how i've been using knoppix for the past month or so: It's running from a hard disk partition, but I don't have to dual boot or mess around with the Master Boot Record or use LILO or anything, all I have to do is make sure the Knoppix CD is in the CDROM rive at boot up
Similar Threads
-
By ku637 in forum General Support
Replies: 2
Last Post: 07-15-2005, 07:51 PM
-
By Pix21 in forum MS Windows & New to Linux
Replies: 0
Last Post: 02-12-2005, 03:15 PM
-
By xdream in forum General Support
Replies: 7
Last Post: 09-16-2004, 11:21 PM
-
By metavoid in forum General Support
Replies: 9
Last Post: 07-03-2004, 10:08 AM
-
By Panada in forum General Support
Replies: 9
Last Post: 04-12-2004, 02:08 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Lot of 10pcs Brocade 57-1000012-01 8Gbps SWL 850nm SFP+ Optical Transceivers
$19.00
Cisco Meraki MA-SFP-1GB-SX 1000BASE-SX SFP Transceiver Module
$24.99
Cisco GLC-FE-100LX 100BASE-LX SFP Transceiver Module
$15.59
Cisco GLC-FE-100LX-RGD 100BASE-LX SFP Transceiver Module
$17.99
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
SFP-10G-SR Original Cisco 10GBASE-SR SFP+ V02 Multi mode Transceiver 10-2415-02
$5.00
Brand New Cisco GLC-LH-SMD 1000BASE-LX/LH SFP Module 1310nm 10km SMF LC
$13.89
Mellanox Original MFM1T02A-SR 10GbE 10GBASE-SR SFP+ Transceiver
$9.00
LOT OF 20 Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module
$89.00
NEW Sealed Cisco SFP-10G-SR-S 10G SR SFP+ Module 850nmMM *US Shipping*
$15.00