I have two machines, one older and my linux machine, and a new one both have DLink DE503+ DEC Tulip based NIC cards.
Both exhibt the SAME BEHAVIOR when booting V3.8 CeBit the HARD LOCKUP if I allow DHCP or use netcardconfig.
I have tried NO APM, PCMCIA, APIC=off etc. with no sucess the ONLY WAY to boot to an working enviroment, sans network, is NODHCP.
lspci, dmesg, and miitool info follows:
These work GREAT in V3.7 under 2.4.x Kernel, I was hoping I could upgrade to the latest and greatest even on my ancient K6 with the 2.6.x Kernel but thats not looking promosing.
Any one have any suggestions.
Code:x]$ lspci -v 0000:00:00.0 Host bridge: VIA Technologies, Inc. VT82C595/97 [Apollo VP2/97] (rev 03) Flags: bus master, 66MHz, medium devsel, latency 32 0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C586/A/B PCI-to-ISA [ApolloVP] (rev 27) Flags: bus master, medium devsel, latency 0 0000:00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Flags: bus master, medium devsel, latency 32 I/O ports at 6000 [size=16] 0000:00:09.0 VGA compatible controller: Trident Microsystems TGUI 9660/938x/968x (rev d3) (prog-if 00 [VGA]) Flags: bus master, medium devsel, latency 32 Memory at e0000000 (32-bit, non-prefetchable) [size=4M] Memory at e0800000 (32-bit, non-prefetchable) [size=64K] Memory at e0400000 (32-bit, non-prefetchable) [size=4M] 0000:00:0a.0 Multimedia audio controller: Yamaha Corporation YMF-724 (rev 05) Subsystem: Yamaha Corporation YMF724-Based PCI Audio Adapter Flags: bus master, medium devsel, latency 32, IRQ 11 Memory at e0810000 (32-bit, non-prefetchable) [size=32K] Capabilities: <available only to root> 0000:00:0b.0 Ethernet controller: Digital Equipment Corporation DECchip 21041 [Tulip Pass 3] (rev 21) Subsystem: D-Link System Inc DE-530+ Flags: bus master, medium devsel, latency 96, IRQ 10 I/O ports at 6200 [size=128] Memory at e0818000 (32-bit, non-prefetchable) [size=128] knoppix@1[knoppix]$ lsmod Module Size Used by snd_mixer_oss 18688 0 snd 46308 1 snd_mixer_oss via_agp 11264 0 sworks_agp 10912 0 sis_agp 9988 0 nvidia_agp 9756 0 intel_mch_agp 11792 0 intel_agp 22044 0 efficeon_agp 10144 0 ati_agp 10380 0 amd64_agp 13640 0 amd_k7_agp 9740 0 ali_agp 9216 0 agpgart 30512 11 via_agp,sworks_agp,sis_agp,nvidia_agp,intel_mch_agp,intel_agp,efficeon_agp,ati_agp,amd64_agp,amd_k7_agp,ali_agp autofs4 18820 1 nls_iso8859_1 7936 0 nls_cp437 9600 0 ymfpci 51212 1 ac97_codec 20108 1 ymfpci uart401 13124 1 ymfpci sound 71812 1 uart401 soundcore 11104 4 snd,ymfpci,sound de4x5 47648 0 parport_pc 38596 0 parport 33480 1 parport_pc 8250 41308 0 serial_core 21120 1 8250 usbhid 42176 0 uhci_hcd 31376 0 pcmcia 21776 0 yenta_socket 21896 0 rsrc_nonstatic 12160 1 yenta_socket pcmcia_core 42272 3 pcmcia,yenta_socket,rsrc_nonstatic apm 22252 2 rtc 13772 0 unionfs 816404 1 cloop 18848 1 sbp2 24456 0 ohci1394 33028 0 ieee1394 300600 2 sbp2,ohci1394 usb_storage 63296 0 ub 18332 0 ohci_hcd 21896 0 ehci_hcd 31752 0 usbcore 101496 7 usbhid,uhci_hcd,usb_storage,ub,ohci_hcd,ehci_hcd knoppix@1[knoppix]$ mii-tool SIOCGMIIPHY on 'eth0' failed: Operation not permitted SIOCGMIIPHY on 'eth1' failed: Operation not permitted SIOCGMIIPHY on 'eth2' failed: Operation not permitted SIOCGMIIPHY on 'eth3' failed: Operation not permitted SIOCGMIIPHY on 'eth4' failed: Operation not permitted SIOCGMIIPHY on 'eth5' failed: Operation not permitted SIOCGMIIPHY on 'eth6' failed: Operation not permitted SIOCGMIIPHY on 'eth7' failed: Operation not permitted no MII interfaces found knoppix@1[knoppix]$ dmesg Linux version 2.6.11 (root@Knoppix) (gcc-Version 3.3.5 (Debian 1:3.3.5-8)) #6 SMP Wed Feb 23 09:15:46 CET 2005 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000000a000000 (usable) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 160MB LOWMEM available. On node 0 totalpages: 40960 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 36864 pages, LIFO batch:9 HighMem zone: 0 pages, LIFO batch:1 DMI 2.0 present. ACPI: Unable to locate RSDP Built 1 zonelists Kernel command line: ramdisk_size=100000 init=/etc/init lang=de apm=power-off vga=791 initrd=minirt.gz nomce quiet BOOT_IMAGE=knoppix BOOT_IMAGE=linux lang=us screen=800x600 vsync=60 nodhcp nodma __iounmap: bad address c00fffd9 No local APIC present or hardware disabled mapped APIC to ffffd000 (01242000) Initializing CPU#0 PID hash table entries: 1024 (order: 10, 16384 bytes) Detected 337.487 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 156380k/163840k available (1829k kernel code, 6916k reserved, 924k data, 296k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 661.50 BogoMIPS (lpj=330752) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: 008021bf 808029bf 00000000 00000000 0000000000000000 00000000 CPU: After vendor identify, caps: 008021bf 808029bf 00000000 00000000 00000000 00000000 00000000 Enabling new style K6 write allocation for 160 Mb CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line) CPU: After all inits, caps: 008021bf 808029bf 00000000 00000002 00000000 00000000 00000000 Checking 'hlt' instruction... OK. Checking for popad bug... OK. CPU0: AMD-K6(tm) 3D processor stepping 0c per-CPU timeslice cutoff: 182.79 usecs. task migration cache decay timeout: 1 msecs. SMP motherboard not detected. Local APIC not detected. Using dummy APIC emulation. Brought up 1 CPUs CPU0 attaching sched-domain: domain 0: span 00000001 groups: 00000001 checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 1046k freed NET: Registered protocol family 16 EISA bus registered PCI: PCI BIOS revision 2.10 entry at 0xfaf80, last bus=0 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20050211 ACPI: Interpreter disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI: disabled PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00fbb50 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbb78, dseg 0xf0000 PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver SCSI subsystem initialized PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI: Via IRQ fixup audit: initializing netlink socket (disabled) audit(1111253036.036:0): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API Activating ISA DMA hang workarounds. isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found i8042: ACPI detection disabled serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:07.1 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt82c586a (rev 27) IDE UDMA33 controller on pci0000:00:07.1 ide0: BM-DMA at 0x6000-0x6007, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0x6008-0x600f, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... hda: WDC AC38400L, ATA DISK drive hdb: ATAPI CD-ROM DRIVE 32X MAXIMUM, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: WDC AC34000L, ATA DISK drive hdd: CRW6206A, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 Probing IDE interface ide2... Probing IDE interface ide3... Probing IDE interface ide4... Probing IDE interface ide5... hda: max request size: 128KiB hda: 16514064 sectors (8455 MB) w/256KiB Cache, CHS=16383/16/63 hda: cache flushes not supported hda: hda1 hda2 < hda5 hda6 hda7 > hdc: max request size: 128KiB hdc: 7814016 sectors (4000 MB) w/256KiB Cache, CHS=7752/16/63 hdc: cache flushes not supported hdc: hdc1 hdc2 hdb: ATAPI 27X CD-ROM drive, 120kB Cache Uniform CD-ROM driver Revision: 3.20 hdd: ATAPI 6X CD-ROM CD-R/RW drive, 384kB Cache libata version 1.10 loaded. mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard on isa0060/serio0 input: ImPS/2 Generic Wheel Mouse on isa0060/serio1 EISA: Probing bus 0 at eisa0 Cannot allocate resource for EISA slot 6 EISA: Detected 0 cards. NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 8Kbytes TCP established hash table entries: 8192 (order: 5, 131072 bytes) TCP bind hash table entries: 8192 (order: 4, 98304 bytes) TCP: Hash tables configured (established 8192 bind 8192) NET: Registered protocol family 1 NET: Registered protocol family 15 RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). seagate: ST0x/TMC-8xx not detected. Failed initialization of WD-7000 SCSI card! usbcore: registered new driver usbfs usbcore: registered new driver hub ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ub: sizeof ub_scsi_cmd 64 ub_dev 2504 usbcore: registered new driver ub Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. ieee1394: Initialized config rom entry `ip1394' sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org> ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1) Unable to identify CD-ROM format. VFS: Can't find an ext2 filesystem on dev hda. FAT: invalid media value (0xb9) VFS: Can't find a valid FAT filesystem on dev hda. ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A cloop: Initializing cloop v2.02 cloop: loaded (max 8 devices) cloop: /cdrom/KNOPPIX/KNOPPIX: 29809 blocks, 65536 bytes/block, largest block is 65562 bytes. ISO 9660 Extensions: RRIP_1991A Registering unionfs version $Id: main.c,v 1.82 2005/02/08 15:17:38 cwright Exp $ Freeing unused kernel memory: 296k freed Real Time Clock Driver v1.12 apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) Linux Kernel Card Services options: [pci] [cardbus] [pm] USB Universal Host Controller Interface driver v2.2 usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] 0000:00:0b.0: DC21041 at 0x6200, h/w address 00:40:05:50:47:d8, and requires IRQ10 (provided by PCI BIOS). de4x5.c:V0.546 2001/02/22 davies@maniac.ultranet.com PCI: 0000:00:0a.0 has unsupported PM cap regs version (1) ymfpci: YMF724 at 0xe0810000 IRQ 11 ac97_codec: AC97 Audio codec, id: AKM1 (Asahi Kasei AK4542) Adding 249944k swap on /dev/hdc1. Priority:-1 extents:1 Linux agpgart interface v0.100 (c) Dave Jones knoppix@1[knoppix]$
Seagate Exos X16 ST14000NM001G 14TB 512E SATA 6Gb/s 3.5" Enterprise Hard Drive
$157.99
WD 16TB Elements Desktop, Certified Refurbished Hard Drive - RWDBWLG0160HBK-NESN
$174.99
Seagate Exos X22 ST20000NM004E 20TB 512E SATA 6Gb/s 3.5" Enterprise Hard Drive
$268.99
$59.99
Seagate Exos 7E10 ST2000NM000B 2TB 7200RPM SATA 6.0Gb/s 3.5" Internal Hard Drive
$29.99
HGST Ultrastar DC HC520 12TB SATA 6Gb 256MB 3.5" Enterprise HDD- HUH721212ALE601
$82.99
HGST Ultrastar HE10 HUH721010ALE600 10TB SATA 6Gb/s 7200RPM 3.5" Enterprise HDD
$74.99
2 PACK Seagate ST1000LM035 Mobile HDD 1TB 2.5" SATA III Laptop Hard Drive
$27.25
Seagate ST12000NM0538 Exos X14 12TB 3.5" SATA 6Gbps 3.5" Enterprise Hard Drive
$45.96
CISCO UCS-HD10T7KL4KN 10TB 7.2K 256MB 12GB SAS-3 3.5'' HUH721010AL4200 DRIVE
$249.97