At the bootup Knoppix 3.8 splash screen, type:
knoppix nodhcp
I am using Knoppix 3.6. and 3.7 without any problems with always the same standard hardware. Booting Knoppix 3.8 stops at recognizing eth0, wainting on DHCP - no way going on. There is a DSL router with DHCP server.
I tried to boot with parameter "expert" but there was no possibility to interact at eth0 or ignore.
Who knows ta solution for this problem?
Reinhart.
At the bootup Knoppix 3.8 splash screen, type:
knoppix nodhcp
Thnx !
Finally I found this parameter [nodhcp] by myself and used it, but after starting Knoppix I cannot install the network card by hand. The system freezes totally after the input of the correct IP addresses.
What kind of card?Originally Posted by rgruhn
I have the same issue with DEC 21041 Tulip based cards under 2.6.x kernel
Reference: http://www.knoppix.net/forum/viewtopic.php?t=17894
I too have tried to do the nodhcp, rmmod or modprobe -r to remove the module and put a new module for a LAN driver in with out success.
So I am sticking to V3.7 under 2.4.x kernel, and since newer versions of Knoppix will only include 2.6 will just have to wait till what ever the bug is, is resolved.
It is an Intel 21143 fast ethernet PCI adapter.
I 've read the thread you pointed to - may be it is a bug in the 2.6.xx kernel. because I had the same problem with knoppix 3.7 and the 2.6 kernel! I only use the 2.4 and hope the problem will be fixed soon.
Thanks so much.
I think it is but I need to compile some evidence to support this.Originally Posted by rgruhn
Thanks for the info on the card, can you possible post a lspci -v and dmesg with the key parts for reference.
Thanks!
I think my problem is just the same as the well known with a DEC-Chip!
Here is the information:
lspci:
0000:02:0b.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 41)
Flags: bus master, medium devsel, latency 96, IRQ 23
I/O ports at e880 [size=128]
Memory at f7fff800 (32-bit, non-prefetchable) [size=1K]
Expansion ROM at f7f80000 [disabled] [size=256K]
DMESG:
de4x5.c:V0.546 2001/02/22 davies@maniac.ultranet.com
Intel 810 + AC97 Audio, version 1.01, 07:27:43 Feb 23 2005
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17
Is this any help, from dmesg and lspci?
Something related to IRQs?
____________________________________
PCI: Found IRQ 9 for device 0000:01:02.0
PCI: Sharing IRQ 9 with 0000:00:1f.3
PCI: Sharing IRQ 9 with 0000:00:1f.5
IRQ routing conflict for 0000:01:02.0, have irq 5, want irq 9
0000:01:02.0: DE434/5 at 0x7880, h/w address 00:00:92:91:2b:78,
and requires IRQ5 (provided by PCI BIOS).
de4x5.c:V0.546 2001/02/22 davies@maniac.ultranet.com
__________________________________________________ __________________
0000:01:02.0 Ethernet controller: Digital Equipment Corporation DECchip 21040 [Tulip] (rev 23)
Flags: bus master, medium devsel, latency 96, IRQ 5
I/O ports at 7880 [size=128]
Memory at febeff80 (32-bit, non-prefetchable) [size=128]
I'm a newbie in this area of linux. Would changing IRQ help? How do I do that in linux?
Thanks.
Dave
Some progress thanks to Mepis Forum. Based on
http://www.mepis.org/node/2485?from=...ts_per_page=30
near bottom of page, I tried
rmmod de4x5
modprobe de2104x
ifconfig eth0 up
ifconfig
pump
Now eth0 seems to be up, but still no internet.
dmesg | tail shows eth0: no IPv6 routers present
What next?
Hmmm, Ubuntu 5.04 gets eth0 up and internet connection up almost immediately after starting to install. Ubuntu uses de2104x and dhclient (instead of pump).
So would dhclient be better with Knoppix kernel 2.6.x than pump, for my ancient DECchip 21040?
How to do that without installing Knoppix?
Thanks.
Dave
1TB Samsung 840 EVO Internal 2.5" SATA III SSD MZ7TE1T0HMHP Solid State Drive
$69.83
SM883 HXM7404Q 2.5 Samsung 960GB SATA6.0Gbps MZ7KH960HAJR-00005 MZ-7KH9600 SSD
$95.00
1.92TB Samsung PM863a SSD MZ-7LM1T9N SATA MZ7LM1T9HMJP-00005 Solid State Drive
$148.00
960GB Samsung M.2 PM983 SSD PCIe NVMe 22110 Solid State Drive MZ1LB960HAJQ-00007
$74.68
Patriot P210 128GB 256GB 512GB 1TB 2TB 2.5" SATA 3 6GB/s Internal SSD PC/MAC Lot
$14.99
Netac 1TB 2TB 512GB Internal SSD 2.5'' SATA III 6Gb/s Solid State Drive lot
$13.99
Fanxiang SSD 512GB 1TB 2TB 4TB 2.5'' SSD SATA III Internal Solid State Drive lot
$13.99
Fanxiang SSD 512GB 1TB 2TB 4TB 2.5''SATA III Internal Solid State Hard Drive LOT
$19.99
M.2 NVMe SSD 128GB 256GB 512GB Single Notch with Windows Installed 10 / 11
$80.99
SAMSUNG SSD 870 EVO 2.5" SATA III Solid State Drive 2TB 1TB 250GB 500GB LOT
$172.15