HD installation doesn't work?

[SmallLinuxUser]

I was able to open the file as root. Hope, I don't flood the screen too much:

# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# ---------------       `install-mbr(8)', `/usr/share/doc/lilo/',
#                       and `/usr/share/doc/mbr/'.

# Remove this line when you are done configuring. -KK
"! Please edit /etc/lilo.conf before running lilo!"

# +---------------------------------------------------------------+
# |                        !! Reminder !!                         |
# |                                                               |
# | Don't forget to run `lilo' after you make changes to this     |
# | conffile, `/boot/bootmess.txt', or install a new kernel.  The |
# | computer will most likely fail to boot if a kernel-image      |
# | post-install script or you don't remember to run `lilo'.      |
# |                                                               |
# +---------------------------------------------------------------+

# Support LBA for large hard disks.
#
lba32

# Specifies the boot device.  This is where Lilo installs its boot
# block.  It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda

# Specifies the device that should be mounted as root. (`/')
#

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller.  Using `compact' is especially recommended when
# booting from a floppy disk.  It is disabled here by default
# because it doesn't always work.
#
# compact

# Installs the specified file as the new boot sector
#
install=/boot/boot-menu.b
backup=/dev/null

# Specifies the location of the map file
#
map=/boot/map

# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration.  If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well.  Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000

# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
# delay=20
timeout=100

# You can put a customized boot message up if you like.  If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress.  `single-key' goes with the `alias' lines in the
# `image' configurations below.  eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
#	prompt
#	single-key
#	delay=100
#	timeout=100

# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#
vga=normal

# Kernel command line options that apply to all installed images go
# here.  See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""

# Boot up Linux by default.
#
default=Knoppix

image=/vmlinuz
	append="lang=de apm=power-off hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi vga=791 quiet BOOT_IMAGE=knoppix"
	root=/dev/hda5
	label=Knoppix
	read-write
#	restricted
#	alias=1

#image=/vmlinuz.old
#	label=Linux-OLD
#	read-only
#	optional
#	restricted
#	alias=2

# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
#	label=HURD
#	restricted
#	alias=3

What can I do?

[fingers99]

OK, to edit it, open up a Terminal and type:

su <return>
(prompt for root password -- type it in) <return>
vim /etc/lilo.conf <return>

(Alternatively, if that doesn't work, try sudo vim /etc/lilo.conf)

vim will pop up with lilo.conf loaded, but the colours will be horrible! Go to >Settings>Schema>Vim Colours (towards the bottom). Hit the "i" key to get into insert mode. Move the cursor with the arrow keys to the line

"! Please edit /etc/lilo.conf before running lilo!"

and type a hash "#" in front of it: bash sees # as a comment, which tells it "ignore this line".

So you have

#"! Please edit /etc/lilo.conf before running lilo!"

Hit the [esc] key to enter command mode.

Type

ZZ

and you're finished with vim.


Now run

/sbin/lilo

(alternatively sudo /sbin/lilo)

and that's it.

[SmallLinuxUser]

Thanks, I will try it next weekend when I'm back home. I hope, it works then...