Try booting with some cheat codes:
knoppix nodma
knoppix acpi=off
Its is probably the DMA which is turned on by default that is causing the problems.
I am completely new to Linux, but thought I'd have a try how it feels and then maybe switch to it.
However even my first trial didn't work.
I use XP Home SP2
When the computer boots on the Knoppix 3.7 CD I get the first screen with the two pinguins on top and then the following message:
I would really like to try out Linux.Code:Welcome to the KNOPPIX live Linux-on-CD Scanning for USB/Firewall devices - done Enabling DMA acceleration for hda [HL-DT-STDVDRRW GWA-4161B] Enabling DMA acceleration for hdd [CD-RW CR52] Enabling DMA acceleration for hdg [Samsung SP1213C] Accessing KNOPPIX CD ROM on dev/scdo.../modules/cloop.o: init module: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters Can't find Knoppix filesystem, sorry. Dropping you to a (very limited) shell. Press reset button to quit. Additional built-in commands available: cat mount umount insmod rmmod lsmod Knoppix#
If anyone has any ideas what to do, please let me know.
Please remember that I'm not familiar with Linux commands.
Thanks
Joey
Try booting with some cheat codes:
knoppix nodma
knoppix acpi=off
Its is probably the DMA which is turned on by default that is causing the problems.
I have the same problem.
I boot from an external usb cdrom, and get the same error message, Knoppix 3.9.
How can I boot with Knoppix?
I'm getting the same issue upon boot. But I believe it's due to the 2.6 kernel.
The guide here (http://www.thinkwiki.org/wiki/Instal...a_Thinkpad_T43) states that you should boot with a 2.4 kernel - my problem is I can't figure out how to specify the 2.4 kernel.
Any help would be appreciated.
Underscore - thanks
For me "nodma" worked just fine and Linux booted without further problems.... that is, no booting problems.
I still got other problems though, that stop me from using Linux so far: I can't get the internet connection to work, but I guess that's for another forum on this site.
I tried the ADSL/PPP config application under "system" but it doesn't seem to be able to activate my modem. Another aplication under "Internet" that looks for hardware found just "etc0" whatever that means. But that didn't get me much further.
I use an external USB ADSL modem and I get the feeling that the problem is not the connection to my provider, but before that - that my modem isn't recognized.
Then again, I don't know enough about Linux to know how I can find out what exactly IS the problem. How does one check if hardware is recognized and properly installed? (Where in the "device manager" of Windows). How do I check if the problem is the modem instalation or the connection?
Thanks for any further help.
A-Tech 8GB DDR3 1600 PC3-12800 Laptop SODIMM 204-Pin Memory RAM PC3L DDR3L 1x 8G
$13.99
Samsung 16GB 2Rx4 PC4-2133P DDR4-17000 1.2V RDIMM ECC Registered Server Memory
$16.29
HyperX FURY DDR3 8GB 16GB 32GB 1600 MHz PC3-12800 Desktop RAM Memory DIMM 240pin
$12.90
A-Tech 16GB 2 x 8GB PC3-12800 Laptop SODIMM DDR3 1600 Memory RAM PC3L 16G DDR3L
$27.98
A-Tech 8GB PC3-12800 Desktop DDR3 1600 MHz Non ECC 240-Pin DIMM Memory RAM 1x 8G
$13.99
Kingston HyperX FURY DDR3 8GB 16GB 32G 1600 1866 1333 Desktop Memory RAM DIMM
$13.25
8GB PC3L-12800S 1600MHz SODIMM DDR3 RAM | Grade A
$12.00
Samsung 16GB (2x8GB) PC3L-12800S Lap Top Memory RAM
$20.00
A-Tech 256GB 4x 64GB 4Rx4 PC4-19200 ECC Load Reduced LRDIMM Server Memory RAM
$287.96
Samsung 64GB 4DRx4 PC4-2400 LRDIMM DDR4-19200 ECC Load Reduced Server Memory RAM
$71.99