Try booting with some cheat codes:
knoppix nodma
knoppix acpi=off
Its is probably the DMA which is turned on by default that is causing the problems.
I am completely new to Linux, but thought I'd have a try how it feels and then maybe switch to it.
However even my first trial didn't work.
I use XP Home SP2
When the computer boots on the Knoppix 3.7 CD I get the first screen with the two pinguins on top and then the following message:
I would really like to try out Linux.Code:Welcome to the KNOPPIX live Linux-on-CD Scanning for USB/Firewall devices - done Enabling DMA acceleration for hda [HL-DT-STDVDRRW GWA-4161B] Enabling DMA acceleration for hdd [CD-RW CR52] Enabling DMA acceleration for hdg [Samsung SP1213C] Accessing KNOPPIX CD ROM on dev/scdo.../modules/cloop.o: init module: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters Can't find Knoppix filesystem, sorry. Dropping you to a (very limited) shell. Press reset button to quit. Additional built-in commands available: cat mount umount insmod rmmod lsmod Knoppix#
If anyone has any ideas what to do, please let me know.
Please remember that I'm not familiar with Linux commands.
Thanks
Joey
Try booting with some cheat codes:
knoppix nodma
knoppix acpi=off
Its is probably the DMA which is turned on by default that is causing the problems.
I have the same problem.
I boot from an external usb cdrom, and get the same error message, Knoppix 3.9.
How can I boot with Knoppix?
I'm getting the same issue upon boot. But I believe it's due to the 2.6 kernel.
The guide here (http://www.thinkwiki.org/wiki/Instal...a_Thinkpad_T43) states that you should boot with a 2.4 kernel - my problem is I can't figure out how to specify the 2.4 kernel.
Any help would be appreciated.
Underscore - thanks![]()
For me "nodma" worked just fine and Linux booted without further problems.... that is, no booting problems.
I still got other problems though, that stop me from using Linux so far: I can't get the internet connection to work, but I guess that's for another forum on this site.![]()
I tried the ADSL/PPP config application under "system" but it doesn't seem to be able to activate my modem. Another aplication under "Internet" that looks for hardware found just "etc0" whatever that means. But that didn't get me much further.
I use an external USB ADSL modem and I get the feeling that the problem is not the connection to my provider, but before that - that my modem isn't recognized.
Then again, I don't know enough about Linux to know how I can find out what exactly IS the problem. How does one check if hardware is recognized and properly installed? (Where in the "device manager" of Windows). How do I check if the problem is the modem instalation or the connection?
Thanks for any further help.
LOT QTY 2 of INTEL XEON 10 CORE E5-2690 V2 25MB 3.00GHZ CPU SR1A5
$139.99
HP Workstation Z640 2x Xeon E5-2623V4 32GB Ram 2x 256GB SSD Quadro P620 Linux GA
$186.99
E5-2699V4 Intel Xeon Processor 55M Cache, 2.20 GHz SR2JS CM8066002022506
$155.00
HP Z440 Workstation Xeon E5-1603 v4 QC 2.80GHz CPU 32GB RAM Quadro K2200
$79.99
Intel Xeon E5-2667 V2 LGA 2011 3.3GHz 8 Core 130W 25MB 8GT/s CPU Processor
$14.99
Intel Xeon E5-2680 V4 CPU 2.4~3.3GHz 14-Core 35M LGA 2011-3 R3 Server SR2N7 120W
$15.99
Intel Xeon E5-2640v4 2.4GHz 10-Core 25MB 90W SR2NZ
$5.45
Intel Xeon E5-2699 v3 2.3GHz 18-Core 45MB 145W LGA2011-3 CPU/Processor SR1XD
$40.99
Matched pair Intel Xeon E5-2667v4 SR2P5 3.20GHz, 8 core, 25MB Processors LGA2011
$62.95
Intel Xeon E5-2667 V4 SR2P5 (3.2GHZ/8-CORE/25MB/135W) PROCESSOR CPU
$29.89