Try booting with some cheat codes:
knoppix nodma
knoppix acpi=off
Its is probably the DMA which is turned on by default that is causing the problems.
I am completely new to Linux, but thought I'd have a try how it feels and then maybe switch to it.
However even my first trial didn't work.
I use XP Home SP2
When the computer boots on the Knoppix 3.7 CD I get the first screen with the two pinguins on top and then the following message:
I would really like to try out Linux.Code:Welcome to the KNOPPIX live Linux-on-CD Scanning for USB/Firewall devices - done Enabling DMA acceleration for hda [HL-DT-STDVDRRW GWA-4161B] Enabling DMA acceleration for hdd [CD-RW CR52] Enabling DMA acceleration for hdg [Samsung SP1213C] Accessing KNOPPIX CD ROM on dev/scdo.../modules/cloop.o: init module: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters Can't find Knoppix filesystem, sorry. Dropping you to a (very limited) shell. Press reset button to quit. Additional built-in commands available: cat mount umount insmod rmmod lsmod Knoppix#
If anyone has any ideas what to do, please let me know.
Please remember that I'm not familiar with Linux commands.
Thanks
Joey
Try booting with some cheat codes:
knoppix nodma
knoppix acpi=off
Its is probably the DMA which is turned on by default that is causing the problems.
I have the same problem.
I boot from an external usb cdrom, and get the same error message, Knoppix 3.9.
How can I boot with Knoppix?
I'm getting the same issue upon boot. But I believe it's due to the 2.6 kernel.
The guide here (http://www.thinkwiki.org/wiki/Instal...a_Thinkpad_T43) states that you should boot with a 2.4 kernel - my problem is I can't figure out how to specify the 2.4 kernel.
Any help would be appreciated.
Underscore - thanks![]()
For me "nodma" worked just fine and Linux booted without further problems.... that is, no booting problems.
I still got other problems though, that stop me from using Linux so far: I can't get the internet connection to work, but I guess that's for another forum on this site.![]()
I tried the ADSL/PPP config application under "system" but it doesn't seem to be able to activate my modem. Another aplication under "Internet" that looks for hardware found just "etc0" whatever that means. But that didn't get me much further.
I use an external USB ADSL modem and I get the feeling that the problem is not the connection to my provider, but before that - that my modem isn't recognized.
Then again, I don't know enough about Linux to know how I can find out what exactly IS the problem. How does one check if hardware is recognized and properly installed? (Where in the "device manager" of Windows). How do I check if the problem is the modem instalation or the connection?
Thanks for any further help.
OEM Dell 130W HA130PM130 DA130PM130 Laptop Power Adapter Charger 4.5mm 6TTY6 XPS
$26.99
OEM 130W USB-C Type-C Charger for Dell XPS 15 9500 9570 9575 17 9700 DA130PM170
$34.88
Genuine 45W Power Adapter Charger for Dell DA45NM140 0KXTTW 4.5*3.0mm OEM
$16.99
Genuine OEM 65W Dell PA-12 AC Adapter Charger For 928G4 LA65NS2-01 n4010 D531N
$13.99
Genuine OEM Dell 130W AC Adapter Charger Brick Large Tip 19.5V 6.7A
$4.97
OEM Dell Inspiron 11 13 14 15 17 3000 5000 7000 AC Adapter Charger 65W 4.5mm Tip
$10.99
NEW OEM Dell 65W 19.5V Charger AC Power Supply Adapter For LA65NM130 332-1831
$12.99
Genuine OEM 65W USB-C Charger Type-C Adapter for Dell LA65NM190/HA65NM190
$21.99
OEM 65W Adapter Charger for DELL Inspiron 15-5567 5565 P66F AC Power 19.5V 3.34A
$14.89
Genuine OEM Dell 130W 4.5mm Small Tip Adapter Charger 19.5V 6.7A 03JF3H 0M1MYR
$14.65