Can you boot with boot: knoppix 3? Do you get a shell prompt? If you do, can you post the results of 'cat /proc/partitions'?
Regards,
- Robert
http://www.cwelug.org/
Knoppix 3.7..3.9 hang on my Toshiba Satellite 1800-400 laptop by booting:
My harddisk partioning table looks corrupt. Only winxp en winme have no problems
by knoppix 3.7 with kernel 2.6 (knoppix26) don't hang and with fdisk I can see the harddisk table only mounting is not posible
With knoppix 3.9 failsafe works but with fdisk I can't see /dev/hda only in low resolution
Perhaps there is a solution for this problem
Can you boot with boot: knoppix 3? Do you get a shell prompt? If you do, can you post the results of 'cat /proc/partitions'?
Regards,
- Robert
http://www.cwelug.org/
With Knoppix 3.2 there where no problems. The harddisk was fully accessable.
The contents of /proc/partitions was:
~Code:major minor #blocks name 3 0 14749056 hda 3 1 6160896 hda1 3 2 1 hda2 3 5 5630751 hda5 3 6 2955928 hda6 ~
With later versions of Knoppix I have problems with accessing my harddisk
with 3.8 and 3.9 knoppix hang by booting on: "scanning for Harddisk partitions and creating /etc/fstab..."
Hopefully there is an option by booting
Hans
If I understand you correctly, the above was created with Knoppix 3.2. However ...Originally Posted by mln
... you were not even able to get to a shell with Knoppix 3.8 or 3.9. Is that correct?Originally Posted by mln
Probably. Your partitions do not look out of the ordinary. So, I suspect it may be something other than your harddrive, but that's just a guess.Originally Posted by mln
To troubleshoot this, let's stick with Knoppix 3.8 for now. Try booting with boot: knoppix debug -b 3 Using that boot command will cause Knoppix to pause at various stages in the boot process. Just type 'exit' at each shell prompt to move on to the next stage. You will know that you are at the final stage when typing 'exit' does not do anything. If you get that far, type 'init 5' to go into graphics mode.
How far do you get?
Regards,
- Robert
http://www.cwelug.org/
With knoppix 3.8 and 3.9, I must stop at stage 3 else the computer hang on the known failure point.
In stage 3, I can give command: init 5 ; startx
To go to X11. But startx stops with error message
When I give the command: cat /proc/partitions the output is:
when I give the command: fdisk /dev/hdaCode:major minor #blocks name 3 0 14749056 hda 240 0 1966656 cloop0
The computer hangs and display continuely: "hda: lost interrupt"
When I boot knoppix 3.9 with the command: failsafe
Knoppix startup very quickly in grafical mode
Only the harddisk is not recognized.
The commands: 'cat /proc/partitions' and ' fdisk /dev/hda'
gives the same output as above.
Now I can break simple the console application: fdisk
Sorry not a possitiive result
regarts:
Hans
So with the knoppix boot label you only get to stage 3 ...Originally Posted by mln
... but with failsafe you get all the way into graphics mode. So one or more of the cheatcodes that's in the failsafe kernel label helps you boot. My guess would be some combination of nodma, noapm, noapci, acpi=off, but that's just a guess.Originally Posted by mln
Try booting with boot: failsafe debug -b 3. As before, just type 'exit' at each shell prompt to move on to the next stage. When you are at the final stage, typeCan you post the output of both of those commands?Code:hdparm -Cbvg /dev/hda dmesg | tail
Regards,
- Robert
http://www.cwelug.org/
Hello Robert,
1.
Here the requested outputs of knoppix 3.9 after:
dmesg | tailCode:hdparm -Cbvg /dev/hda multcount = 16 (on) IOSupport = 0 (default 16 bits) Unmaskirq = 0 (off) Using dma = 0 (off) Keepsettings = 0 (off) Readonly = 0 (off) Readahead = 256(on) Geometry = 29264/16/63, sectors = 29418912, start = 0 Drive state is: active/idle Busstate = 1 (on)
.... the rest is for other things such as CD: ISO9660 memory etc ...Code:FAT: invalid media value (0xcd) VFS: Can’t find a valid filesystem on dev hda.
2.
When I start up knoppix 3.9 with option ‘no dma’:
Knoppix fb1024x768 screen=1024x768 no dma
Then the laptop startup normally but the harddisk is not accessable
hdparm -Cbvg /dev/hda
dmesg (not interesting parts are removed)Code:multcount = 16 (on) IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 1 (on) keepsettings = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 29264/16/63, sectors = 29498112, start = 0 drive state is: active/idle busstate = 1 (on)
Code:Linux version 2.6.11 (root@Knoppix) (gcc-Version 3.3.5 (Debian 1:3.3.5-12)) #2 SMP Thu May 26 20:53:11 CEST 2005 ........ ........ ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ALI15X3: IDE controller at PCI slot 0000:00:04.0 ACPI: PCI Interrupt 0000:00:04.0[A]: no GSI ALI15X3: chipset revision 195 ALI15X3: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xeff0-0xeff7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xeff8-0xefff, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: TOSHIBA MK1517GAP, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: TOSHIBA DVD-ROM SD-C2502, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 Probing IDE interface ide2... Probing IDE interface ide3... Probing IDE interface ide4... Probing IDE interface ide5... hda: max request size: 128KiB hda: 29498112 sectors (15103 MB), CHS=29264/16/63 hda: cache flushes not supported hda:hda: task_in_intr: status=0x51 { DriveReady SeekComplete Error } hda: task_in_intr: error=0x04 { DriveStatusError } ide: failed opcode was: unknown hda: task_in_intr: status=0x51 { DriveReady SeekComplete Error } hda: task_in_intr: error=0x04 { DriveStatusError } ide: failed opcode was: unknown hda: task_in_intr: status=0x51 { DriveReady SeekComplete Error } hda: task_in_intr: error=0x04 { DriveStatusError } ide: failed opcode was: unknown unknown partition table hdc: ATAPI 24X DVD-ROM drive, 128kB Cache Uniform CD-ROM driver Revision: 3.20 ....... .......
3.
Now when I do the same with knoppix 3.2 (may 2003)
The three partitions are accessable now.
failsafe debug -b 3. No debugger (normal booting knoppix 3.2)
after booting: knoppix screen=1024x768 The output of:
hdparm -Cbvg /dev/hda
Code:multcount = 16 (on) IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 1 (on) keepsettings = 0 (off) readonly = 0 (off) readahead = 8 (on) geometry = 1836/255/63, sectors = 29498112, start = 0 drive state is: active/idle busstate = 1 (on)
and
dmesg (not interesting parts are removed)
Code:Linux version 2.4.20-xfs (root@Knoppix) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 SMP Mit Mär 26 15:37:36 CET 2003 ... ide_setup: hda=scsi ide_setup: hdb=scsi ide_setup: hdc=scsi ide_setup: hdd=scsi ide_setup: hde=scsi ide_setup: hdf=scsi ide_setup: hdg=scsi ide_setup: hdh=scsi .... .... PCI: No IRQ known for interrupt pin A of device 00:04.0. Please try using pci=biosirq. ALI15X3: chipset revision 195 ALI15X3: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xeff0-0xeff7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xeff8-0xefff, BIOS settings: hdc:DMA, hdd:pio hda: TOSHIBA MK1517GAP, ATA DISK drive hdc: TOSHIBA DVD-ROM SD-C2502, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 blk: queue c032bfc4, I/O limit 4095Mb (mask 0xffffffff) hda: 29498112 sectors (15103 MB), CHS=1836/255/63, UDMA(33) ide-cd: passing drive hdc to ide-scsi emulation. Partition check: hda: hda1 hda2 < hda5 hda6 > ..... .....
Greetings
Hans
Just a thought.
The Cheat Code to disable DMA is 'nodma' not 'no dma'.
Sorry but with the command: knoppix nodma the system is hanging on the same point.
But with the command: knoppix no dma the system is booting so as told
As seen in your post:Emphasis mine.Originally Posted by mln
OK, so to summarize:
To turn on/enable DMA: knoppix dma
To turn off/disable DMA: knoppix nodma
'knoppix no dma' with a space between 'no' and 'dma' does not disable DMA but instead enables it. None of the Cheat Codes have spaces in it.
KNOPPIX 9.1 LINUX INSTALL & LIVE DVD
$9.99
$6.40
Linux Knoppix 4.0.2 Installation Disc
$29.99
Knoppix Linux Bootable OS v8.6 "Original Live Operating System" 32G USB Stick
$20.30
$6.00
Acer Aspire One 9 inch Netbook ZG5 512MB RAM 8GB SSD HD Knoppix Linux WiFi VGA
$79.99
Knoppix 3.4 Linux installation CD
$5.00
Knoppix Linux Bootable OS v8.6 "Original Live Operating System" 16G USB Stick
$19.95