-
Senior Member
registered user
Once the KNOPPIX image is booting, its faster than the CD boot. Also, if you're using a boot floppy, loadlin is a lot faster to.
Works for me at least!
Regards,
-
This post for A. Jorge Garcia or anyone who can offer a solution;
At last, after battling all day, I have managed to get Knoppix to run off the hardrive and it will run off any of these batch files:
loadlin.exe vmlinuz lang=e initrd=miniroot.gz load_ramdisk=1 init=/etc/init hdc=ide-scsi vga=791
or:
loadlin.exe vmlinuz lang=e initrd=miniroot.gz quiet BOOT_IMAGE=knoppix
The problem being that the programme loads in German. Elsewhere in this thread someone had the same problem but no-one answered
Finally how can I get it to read my config files which are stored on another partition?
Can you help please?
-
Senior Member
registered user
Did you use the file boot-en.img when extracting vmlinuz and miniroot.gz?
Regards,
-
Senior Member
registered user
loadlin.exe vmlinuz
lang=e initrd=miniroot.gz load_ramdisk=1 init=/etc/init hdc=ide-scsi vga=791
or:
loadlin.exe vmlinuz
lang=e initrd=miniroot.gz quiet BOOT_IMAGE=knoppix
if these are your batch files I believe the language entry should be: lang=en
HTH
rock
-
Senior Member
registered user
Originally Posted by
Ewen
This post for A. Jorge Garcia or anyone who can offer a solution;
At last, after battling all day, I have managed to get Knoppix to run off the hardrive and it will run off any of these batch files:
loadlin.exe vmlinuz lang=e initrd=miniroot.gz load_ramdisk=1 init=/etc/init hdc=ide-scsi vga=791
or:
loadlin.exe vmlinuz lang=e initrd=miniroot.gz quiet BOOT_IMAGE=knoppix
The problem being that the programme loads in German. Elsewhere in this thread someone had the same problem but no-one answered
Finally how can I get it to read my config files which are stored on another partition?
Can you help please?
I also had this German GUI problem. Also I do not have boot-en.img because the ISO file I downloaded was EN.(-as in English version 3.2.)
My solution is to rearrange the batch file so that the lang=en or lang=us comes after init=/etc/init or
"loadlin.exe vmlinuz init=/etc/init lang=us vga=788 xmodule=fbdev initrd=miniroot.gz quiet BOOT_IMAGE=knoppix"
Seems the order of the batch file is significant
note that I reduced the resolution to 800x600(vga=78
Hope this helps
-
RockMumbles... what a stupid error on my part! "Bugger" as they say in Australia, I'm going back to the setup and try again.
Bongski55... I am going to try your .bat file as well
I'll post back with the results.
PS: Can anyone answer my question about getting the programme to read 'myconfig' files saved on a different partition?
Thanks to all for the replies.
-
Senior Member
registered user
Originally Posted by
Ewen
PS: Can anyone answer my question about getting the programme to read 'myconfig' files saved on a different partition?
I can access my files by clicking on the icons(shortcut) of the partitions on the desktop(hda0,hda1,hda2,hda3-I have 4 partitions). The contents are displayed by konqueror. Config files are opened by kwrite.
I am not sure what you really mean by "on a different partition".
-
Bongski55 and RockMumbles... thanks for the batch files... they both work famously.
I am not sure what you really mean by "on a different partition".
Ok... my post was badly worded. I have on my system hda1, hdb1, hdb5, and hdb6.
When I make changes to the Knoppix sytem I go to the Knoppix entry in the Start menu and I sellect Configure/Save Configuration. This gives me the options of what I want saved and the nect requester gives me 'where' I want to save it.
I always save to 'hdb6'. When I start Knoppix from the CD at the boot prompt I type 'knoppix myconfig=scan' and when it boots it finds all the settings and I'm ready to go.
I now have Knoppix saved to my HD and by using the knoppix.bat file (also gleaned from this site) I would like to be able to access the same configuration so that when I boot into the HD version everything will be as I set it up in the saved configuration.
-
Senior Member
registered user
Batch file for boot prompt?
I think what you want is to be able to display the boot prompt. Perhaps a modified batch file can do this.Have not tried this and I am not sure it would work because of the loadlin.exe. I think loadlin is programmed to go through the boot process without going thru the boot prompt?
Any comments?
-
Originally Posted by
RockMumbles
just FAT32
Has anyone managed to boot a KNOPPIX image in a NTFS filesystem from a floppy disk using the NTFS drivers http://linux-ntfs.sourceforge.net/?
Similar Threads
-
By Katagia in forum Networking
Replies: 0
Last Post: 05-01-2005, 10:21 AM
-
By JoeHA in forum German Forum
Replies: 2
Last Post: 01-17-2005, 02:29 PM
-
By dougvega in forum General Support
Replies: 5
Last Post: 10-28-2004, 01:31 AM
-
By JeauxBleaux in forum General Support
Replies: 4
Last Post: 05-31-2003, 06:09 PM
-
By Jon in forum General Support
Replies: 3
Last Post: 05-02-2003, 05:19 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
WD_BLACK 1TB 2.5-inch Performance Hard Drive - WD10SPSX
$69.99
WD_BLACK 1TB D30 Game Drive SSD for Xbox Summer Collection - WDBAMF0010BSU-WESN
$109.99
SanDisk 1TB Ultra Dual Drive Go USB Type-C Flash Drive, Black - SDDDC3-1T00-G46
$109.99
WD 1TB Elements SE SSD, Portable External Solid State Drive - WDBAYN0010BBK-WESN
$79.99
1TB Samsung 850 Pro Series 2.5" SATA 3 SSD MZ-7KE1T0BW HDD hard drive MZ-7KE1T0
$59.99
SEAGATE ST1000DM003 1TB SATA 3.5”HARD DRIVE
$11.19
Patriot P210 128GB 256GB 512GB 1TB 2TB 2.5" SATA 3 6GB/s Internal SSD PC/MAC Lot
$19.99
Samsung - Geek Squad Certified Refurbished 870 EVO 1TB SATA Solid State Drive
$67.99
1TB/2TB USB 3.0 Flash Drive Thumb U Disk Memory Stick Pen PC Laptop Storage lot
$80.39
Toshiba DT01ABA100V 3.5" SATA Internal Hard Drive 1TB Tested/Wiped
$15.00