good idea, most should be possible w/o remastering by simply changing the configs, but:
why the extra external adsl router? Knoppix can do that as well
How about a superserver.
I have tried over many nights to create this monstrosity, but so far not much luck.
A 3 interface box with an ethernet ADSL router, Wireless access point, and my home network.
Use knoppix Terminal server for internal net-boot clients (just dhcp for windows), and Samba server.
use dyndns and ddclient to tell me where it is when away from home.
frees/wan for WiFi access when at home on my notebook.
bind resolving my internal ip's and forwarding to the proxy on my adsl router.
tranparent squidcache to service redirects from iptables. (fwbuilder?)
getmail, gotmail, and yosucker to get my mail.
mrtg to keep my ISP honest. (Have an issue with them at the moment, They have been metering at least 25% more than what my router shows)
imp to serve my mail via apache https when away from home.
from internet terminate ssh, https, ipsec-vpn (with nat traversal)
So far have only ddclient, and getmail working. Now stuck on imp.
good idea, most should be possible w/o remastering by simply changing the configs, but:
why the extra external adsl router? Knoppix can do that as well
Any method would be good.
I just happen to have an external router.
Perhaps even supporting diald? This may limit external access though?
and not to forget webmin
Haven't had much success with webmin.
Installed it on two separate HPUX boxes. And played with it for a few minutes on each. But got very difficult once I tried to do anything serious with it.
Ended up using vi
For my experience, I use knoppix as a workstation, and e-smith for my home server.
I also use e-smith for the server, but having all of the above done with Knoppix would also be fine. As for webmin, I was able to install it on my home directory (which resides on HD) without any problems.
e-smith looks interesting. Does it run from cd?
No it needs a hd, I think the current versions will need about a 1GB hd, it is hardcoded for a 256MB swap and needs about 300-400mb for the OS.e-smith looks interesting. Does it run from cd?
I've still been using earlier versions because I can get them to run on older hardware with a 500mb hd.
E-smith is a full featured gateway/server package, for internet sharing and file and print sharing, it is very easy to set up, but kind of slow as far as the web interface goes.
rock
Thanks.
I'll think I'll stick with trying to get this stuff to go on knoppix just for the moment.
Have got imp going finally
Cisco SG110 24 Port Gigabit Ethernet Switch w/ 2 x SFP SG110-24
$117.00
Sonicwall 02-SSC-1874 Compatible 10GBASE-T Copper SFP+ RJ-45 30M Transceiver-876
$189.05
GENUINE CISCO DS-SFP-FC32G-SW SFP NEW SEALED SEE PHOTOS SHIPS FREE
$74.99
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
For Cisco SFP-10G-T, Ubiquiti UF-RJ45-10G Module 10G SFP+ to RJ45 10GBase-T
$48.59
NEW Sealed Cisco SFP-10G-SR-S 10G SR SFP+ Module 850nmMM *US Shipping*
$15.00
GENUINE Cisco SFP-GE-T EXT 30-1421-01 USA 1000BASE-T RJ45 SFP Transceiver
$9.99
Lot (10) Dell 0N8TDR 850nm SFP-10G-SR-85C 10Gbs sfp+ FTLX8574D3BNL-FC N8TDR NEW
$68.00
NEW Sealed Cisco SFP-10G-LR 10GBASE-LR SFP+ 1310nm 10km *US Shipping*
$18.00