-
Myconfig with Knoppix 3.9
I have been using Knoppix 3.4 up to now and have always saved my config to my external USB drive which is /mnt/sda1. I loaded Knoppix 3.9 for the first time today and used my usual command at the boot prompt which is <knoppix myconfig=/mnt/sda1> and 3.9 could not find it.
Then I used <knoppix myconfig=scan> and it still could not find it. I discovered later that my USB drive is now known as <uba1>. When I substituted this the config worked. However <uba1> is not mentioned in the /mnt directory but <sda1> is. Whichever description I use makes no difference I still can't open my usb drive.
The only thing I can think of is that the older config still refers to <uba1> as <sda1>.
Any help will be appreciated.
-
Senior Member
registered user
Re: Myconfig with Knoppix 3.9
Originally Posted by
Ewen
The only thing I can think of is that the older config still refers to <uba1> as <sda1>.
Any help will be appreciated.
There was a similar issue with floppyconfig. As a shot in the dark, try booting with boot: knoppix myconfig=/mnt/sda1 -b which will put you in "emergency mode." Then type 'mkdr /mnt/sda1' [1] to create the mountpoint. Type 'exit' to continue booting normally.
Don't guarantee that it'll work, but please post back either way.
Regards,
- Robert
http://www.cwelug.org
[1] Edit: that should read 'mkdir /mnt/sda1'
-
Re: Myconfig with Knoppix 3.9
Thank you rwcitek... I'll try that later tonight and post back
Regards,
-
Myconfig with Knoppix 3.9
I followed your instructions to this point:
root@console[~]# mkdr /mnt/sda1 -b
and Knoppix responded with this:
bash: mkdr: command not found
Back to square one methinks.!
-
Senior Member
registered user
Re: Myconfig with Knoppix 3.9
Originally Posted by
Ewen
root@console[~]# mkdr /mnt/sda1 -b
We both mistyped. Let's try again.
Boot with
Code:
boot: knoppix myconfig=/mnt/sda1 -b
Then once you enter "emergency mode", type this:
Code:
mkdir /mnt/sda1
exit # to leave "emergency mode"
Let us know how it goes.
Regards,
- Robert
http://www.cwelug.org
-
Myconfig with Knoppix 3.9
Perhaps I'm not getting into "emergency mode" because I keep getting this response:
bash: mkdr: command not found
When I type "exit" I'm back at the root # prompt and then it's a "reset" to start again.
Regards,
Ewen
____________________________
I must have made a typo somewhere because I succeeded in getting into emergency mode, the mkdir command was carried out and the boot proceeded. It stopped with this statement:
Filesystem not auto detected. Trying to mount with AES256.
/dev/sda1: no such device or address
Snookered again!
Regards,
Ewen.
-
Myconfig with Knoppix 3.9
I ran into a brick wall every time here so I installed Knoppix on a spare drive instead. All is well now and i must say I quite like it as a debian install. Perhaps you could explain how to get it to recognise my 256meg USB memory stick though.
Many thanks for the previous help,
Regards,
Ewen
Similar Threads
-
By scorpion2782 in forum Hardware & Booting
Replies: 1
Last Post: 11-12-2008, 03:26 PM
-
By lilsirecho in forum Klik
Replies: 3
Last Post: 01-16-2005, 02:21 PM
-
By evilkat in forum General Support
Replies: 0
Last Post: 02-06-2004, 06:52 AM
-
By unamiccia in forum General Support
Replies: 3
Last Post: 01-08-2004, 02:43 AM
-
By DavidTempler in forum General Support
Replies: 5
Last Post: 06-22-2003, 03:36 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Cisco QSFP-100G-LR4-S 100GBASE-LR4 QSFP28, 1310nm, 10km, LC, SMF
$335.99
Cisco SFP-10/25G-CSR-S 10/25GBASE-CSR SFP28, 850nm, 100m, LC,
$54.00
Silicom (PE210G2SPI9A-XR) 10Gb Dual Port SFP+ PCIe Ethernet Adapter Low Profile
$19.99
Cisco SFP-10G-BX40D-I 10GBASE-BX-D BiDi SFP+, 1330nm-TX/1270nm-RX, 40km, LC, SMF
$59.99
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
Genuine Cisco GLC-TE 30-1475-01 V01 1000BASE-T SFP COPPER RJ-45 100M TRANSCEIVER
$11.90
NEW Sealed Cisco SFP-10G-LR 10GBASE-LR SFP+ 1310nm 10km *US Shipping*
$18.00
Brand New Cisco GLC-LH-SMD 1000BASE-LX/LH SFP Module 1310nm 10km SMF LC
$13.89
LOT OF 20 Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module
$89.00
10 PCS Cisco GLC-LH-SMD 10-2625-01 1310nm SFP Transceiver Module
$85.00