-
Bootloader and ATA-Raid
Hi Guys,
I have a problem with my Bootloaders(lilo, XP-Boot)! I have a ata-raid system wich is not supportetd by Linux, where my Xp is installed! And a second HD (samsung 120GB) where Linux ist stored! I can't manage that one Bootloader boot both OS! Lilo don't load Xp because the raid...and Xp-Loader (with the bootsec.lin from lilo) only says L 99 99...with linear, cylinders, heads and so on, too!
The only way to boot Linux without Floppy ist writing The MBR from Linux to the 2 HD...but how cann i tell the XP-Loader to start (search) a other MBR???
Whats wrong (with me)???
-
Senior Member
registered user
just curious, how can you know that putting lilo at the MBR of the second HD works ?
-
I tried it already! Made the 2 HD to the first boot device...and voila, BOOTING! (But only linux)
-
Senior Member
registered user
If that is the case, it may have something to do with the disk ID when you are configuring LILO. You may need to read the LILO documentation about this.
I assume you have already tried dd the MBR(on the second HD) and allows NT boot loader to load it.
-
Yes i already tried "dd if=/dev/hda1 bs=512 count=1 of=/boot/bootsec.lin" (right syntax?)
hda1=second Linux HD
hdg+hde=Xp Raid!
Wich type of ID you mean? I tried everything i think...bios=0x81-0x86!
But the problem is...i don't know which ID exactly it is!
-
Senior Member
registered user
My WAG:
When you boot with XP, your Linux disk is no longer hda but being pushed to say hdb/hdc/hdd etc.(I believe bios=0x80 is hda)
I think this is similar to the case of bootable SCSI card. you may google and see if there is additional information.
May be just set a number of lilo entries with something like the following :
disk=/dev/hda
bios=0x80-5
such that you have 6 LILO entries and see if any one of them works, without running the lilo again and again.
BTW , you said if=/dev/hda1, shouldn't it be if=/dev/hda if you ask LILO to write to MBR ?
Originally Posted by
RealNeo
Yes i already tried "dd if=/dev/hda1 bs=512 count=1 of=/boot/bootsec.lin" (right syntax?)
hda1=second Linux HD
hdg+hde=Xp Raid!
Wich type of ID you mean? I tried everything i think...bios=0x81-0x86!
But the problem is...i don't know which ID exactly it is!
-
that was the code to read out the bootsec.lin from the rootpart. which is hda1! I try now the different ID...again
-
Senior Member
registered user
Originally Posted by
RealNeo
that was the code to read out the bootsec.lin from the
rootpart. which is hda1! I try now the different ID...again
What does the line "boot=XYZ" look like in your /etc/lilo.conf look like?
That's the device where lilo wrote its boot sector. MBR would be hdX,
a partition would add a number to this, eg hdXn.
Look at that "XYZ", value and use it in your dd command, as "if" parameter.
You probably cannot copy this bootsector directly to your XP C: drive,
not if it is formatted as NTFS. Instead send the boot sector to a (FAT) floppy:
dd if=/dev/XYZ bs=512 count=1 of=/dev/fd0/knoppix.bs
Then boot under XP, copy the floppy file to C:\knoppix.bs, and add
an entry for it in your C:\boot.ini file:
C:\knoppix.bs="Knoppix"
These are generic instructions, which might be thwarted by the RAID
controller affecting your device names, and the boot disk switching...
Anyway, since you'll only be writing to floppy, there's no risk involved.
It may be worth a try....
-
I tried both boot=hda and hda1 (hda1 for non MBR install with a bootsctor file)! And both is not working....again and again L 99 99 99....
And ID, Sector and Head adresses won't work!!!....and the biggest problem is...i have smoked 30 cigartettes since the beginging of this s**t!
Similar Threads
-
By bluenose50 in forum General Support
Replies: 2
Last Post: 01-28-2005, 10:15 PM
-
By Alterscape in forum Hdd Install / Debian / Apt
Replies: 8
Last Post: 12-29-2004, 01:54 AM
-
By rrfish72 in forum General Support
Replies: 12
Last Post: 07-17-2004, 05:25 PM
-
By mschievano in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 05-12-2004, 06:34 PM
-
By in forum Hdd Install / Debian / Apt
Replies: 3
Last Post: 01-27-2003, 09:42 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Cisco 2801 Integrated Services Router ISR w/ WIC-1DSU-1-v2, VIC2-2FXS CISCO2801
$59.99
Cisco 2900 Series CISCO2951/K9 v03 Integrated Services Router
$54.99
Cisco Nexus 48-Port 10G SFP+ Switch N9K-9396PX w/ 9K-M12PQ 12-Port 40G QSFP
$249.99
Cisco 2911/K9 Integrated Service Router
$49.99
Cisco WS-C3850-48P-L 48-Port Gigabit 3850 PoE Switch w/ 715W+ C3850-NM-4-1G Mod
$83.00
Cisco QSFP-40G-SR-BD BiDi Short-reach Transceiver, 1 Year Warranty
$17.25
Cisco C3850-NM-2-10G 2 Port Network Exp.Module for 3850
$38.99
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
Cisco WS-C3850-48F-S Catalyst 3850 48x 1GB PoE+ RJ-45 1x Module Switch
$185.00
Cisco Catalyst C9200-48P-A 48 Port Rack Mountable Network Switch
$1000.00