I have a similar LT modem, which I had working under a SuSE distro so it is supported.
I don't want to install KNOPPIX, I want it to boot it on a CD. If I do, I can't use the modem. Anyone solved this problem?
Hey everyone, I got Knoppix installed on my HD and everything looks great with one exception, I can't use my modem. Have to go back to Bill Gates to get online, ycccck. The modem that I have is an internal ActionTec on com 2, it is a winmodembut it is supported. I got the driver ltmodem-2.4.18_8.00a3_i386.deb. I ran uname -r in a terminal to get the kernal version of my Knoppix install and it shows me 2.4.19 and have been unable to locate a driver for that version. The modem show busy everytime I run KPPP to try and log on. I was wondering if this is caused by the driver not being the correct version? Or is there another issue that I am overlooking. I am still a newbie when it comes to Linux and don't really have the time to devote to a full blown study to learn this system right now. Guess it will take me a while. I am very pleased with it I must admit if I could just get past this modem problem, or should I say my problem, mental blackout. I tried DemoLinux 3.00 and I can access my modem with it, the kernal version of that, i.e. Demolinux is 2.4.18 which is why I wonder if this is caused by the kernal version. Would it help if I recompiled the kernal? (another learning experience) I am willing to try if necessary. I will say that I feel Knoppix is a better demo than demolinux and that is why I used it to install to my HD. I greatly appreciate any help I can get with this. Thanks before hand.
Here is additional information that may be helpful
logged in as root, ran "lspci -vv" result for Comm controller below
00:09.0 Communication controller: Lucent Microelectronics 56k WinModem (rev 01)
Subsystem: Lucent Microelectronics LT WinModem 56k Data+Fax+Voice+Dsvd
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort
- <MAbort- >SERR- <PERR-
Latency: 0 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d7009000 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at e800 [size=8]
Region 2: I/O ports at ec00 [size=256]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Could it be a problem with the Interrupt, pin A routed to IRQ 11, shouldn't it be using IRQ 3? If so will I have to remove board and change jumpers?
It puzzles me though as I stated above Demolinux 3.0 has no problem using this modem as it is.
I have a similar LT modem, which I had working under a SuSE distro so it is supported.
I don't want to install KNOPPIX, I want it to boot it on a CD. If I do, I can't use the modem. Anyone solved this problem?
Yes I had the same deal, the modem wouldn't work when running from the CD either. I thought I could correct it after installing. Hmmm, I like Knoppix, but if I can't get this problem resolved I will use a different distro that I can get to work.Originally Posted by Anonymous
Dell SNPTP9W1C/16G 16 GB 2666MHz (PC4-2666) Memory Ram
$34.95
A-Tech 8GB DDR3 1600 PC3-12800 Laptop SODIMM 204-Pin Memory RAM PC3L DDR3L 1x 8G
$13.99
NEW OLOy 16GB 2x8GB KIT DDR4-3000 PC4-24000 Desktop Gaming RAM MD4U0830160BB1ST
$19.99
Micron 8GB DDR4 1Rx16 PC4-3200AA Laptop RAM Memory MTA4ATF1G64HZ-3G2E2
$10.00
Team T-FORCE VULCAN Z 32GB (2 x 16GB) PC RAM DDR4 3200 (PC4 25600) Memory
$54.99
Crucial DDR3L 16GB 1600 2x 8GB PC3-12800 Laptop SODIMM Memory RAM PC3 16G DDR3
$22.45
8GB PC3L-12800S 1600MHz SODIMM DDR3 RAM | Grade A
$12.00
RAMAXEL 16 GB ( 4 GB x 4 sticks ) DDR3L-1600 PC3L-12800U 12800 Desktop RAM - HVD
$11.42
CORSAIR Vengeance RGB 32GB (2 x 16GB) 288-Pin PC RAM DDR5 5600 (PC5 44800) AMD
$94.99
Kingston Fury Beast 32GB (2x16GB) 6000MT/s DDR5 CL36 Desktop Memory Kit of 2 AMD
$80.00