-
System hangs when using a ralink based zaapa wireless card
Hi, I'm a complete profane to Linux, so please be patient
I am using Knoppix v4 with an AMD 900 Mhz 512Mb computer. I've got a Zaapa WiFi card installed with Ralink chipset. It seems to be recognized but the first time I try to scan for networks, it won't see anything. If I try for second time, it just gets frozen.
Questions: Is this card supported? Where can I see if Knoppix is recognizing it? (something like system properties in windows) I have found drivers for the card in Internet, but must be compiled and although I have tried to do it, have no clue why it won't work. I'm a bit lost, as you can see...
Thanks a lot for your time.
Dån
-
I have a similar problem when I boot with KNOPPIX_V4.0.2CD-200509-23-EN.
The boot process stops at:
Network device eth0 detected, DHCP broadcasting for IP. (Backgrounding)
Network device eth1 detected, DHCP broadcasting for IP.
I have a ethernet card and a Foxconn Foxconn WLL-3350 PCI Wireless Adapter which
uses a Ralink chipset. It works just fine with Ubuntu 5.10.
I found that KNOPPIX_V4.0.2CD-200509-23-EN does boot if I use the nodhcp cheat code:
boot: knoppix nodhcp
I can see the card in the Info Center.
KDE -> System -> KInfoCenter (Info Center)
then select PCI in the Index tab
reports the card as:
0000:00:0f.0 Network controller: RaLink Ralink RT2500 802.11 Cardbus Reference Card (rev 01)
Subsystem: RaLink: Unknown device 2450
Flags: bus master, show devsel, latency 32, IRQ 11
Memory at d9000000 (32-bin, non-prefetchable) [size=8k]
Capabilities: <available only to root>
I can get it up and runing with:
KDE -> KNOPPIX -> Network/Internet -> Network card configuration
In the Xdialog select "eth1 Netwerkkarte_1"
and Use DHCP broadcast? Yes
After that the nework is up and running as shown by ifconfig and a working Mozilla Firefox.
It looks like there is some silliness in the booting process that prevents the wireless card from working properly.
I also tried KNOPPIX 3.9 and 3.4 -- neither of them recognize the wireless card as a network interface.
George
-
Same problem here when I boot with the KNOPPIX_V4.0.2CD-200509-23-EN.
I have a Ralink wireless card as well, on an Avertec 6100 series laptop.
The boot process stops at:
Network device eth0 detected, DHCP broadcasting for IP. (Backgrounding)
Network device eth1 detected, DHCP broadcasting for IP. (Backgrounding)
I used the cheat-code as mentioned and it goes to the next line before hanging again (boot: knoppix nodhcp):
Skipping DHCP broadcast/network detection as requested . . .
Automounter started for: floppy cdrom.
_
Any other options? Nevermind.
Looked into the tips and triks under the cheat-codes page and entered the usefull option for Laptops with the previous cheat-code and it worked!
boot: knoppix acpi=off pnpbios=off noapic noapm nodhcp
New problem!
Tried to get my wireless going as mentioned in the previous post:
In the KNOPPIX Menu -> Network/Internet -> Network card configuration
In the Xdialog select "eth1 Netwerkkarte_1"
and Use DHCP broadcast? Yes
and after that it says DHCP broadcast fails
So, I tried "eth0 Netwerkkarte_0" and then it just froze up, I thought Linux didn't freeze up completely?
Any solution for me to get my wireless card working?
-
Yes solution is dont use linux at least knoppix or dont use rt2500 chip based card.
If you wanna use unix like system use PCBSD there my rt2500 (Asus wl-107g) card works.
And ubuntu or kubuntu (5.10) linux work well too with my card.
Similar Threads
-
By jbreazeale in forum Hdd Install / Debian / Apt
Replies: 9
Last Post: 08-12-2006, 03:32 PM
-
By DiabloGN in forum General Support
Replies: 3
Last Post: 04-19-2005, 06:22 AM
-
By techz_boy in forum Hdd Install / Debian / Apt
Replies: 1
Last Post: 09-02-2004, 06:21 PM
-
By joekrahn in forum Ideas
Replies: 1
Last Post: 02-24-2004, 05:20 PM
-
Replies: 3
Last Post: 11-13-2003, 05:52 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
![New Cisco GLC-TE 1G SFP Copper RJ45 100m 1000BASE-T Transceiver Module picture](/store/img/UFgAAOSwrw9l1Cbr/s-l225//New-Cisco-GLC-TE-1G-SFP-Copper-RJ45-100m-1000BASE-.jpg)
New Cisco GLC-TE 1G SFP Copper RJ45 100m 1000BASE-T Transceiver Module
$22.32
![NEW Sealed Cisco SFP-10G-LR 10GBASE-LR SFP+ 1310nm 10km *US Shipping* picture](/store/img/Tb4AAOSwmeVlqJuU/s-l225//NEW-Sealed-Cisco-SFP-10G-LR-10GBASE-LR-SFP-1310nm-.jpg)
NEW Sealed Cisco SFP-10G-LR 10GBASE-LR SFP+ 1310nm 10km *US Shipping*
$18.00
![New HP HPE Aruba J4858D 1G SFP LC SX 850nm 500m MMF XCVR Transceiver Module picture](/store/img/-RQAAOSwv-Rl1Cgp/s-l225//New-HP-HPE-Aruba-J4858D-1G-SFP-LC-SX-850nm-500m-MM.jpg)
New HP HPE Aruba J4858D 1G SFP LC SX 850nm 500m MMF XCVR Transceiver Module
$28.49
![For Cisco SFP-10G-T, Ubiquiti UF-RJ45-10G Transceiver, SFP+ to RJ45 10GBase-T picture](/store/img/H0kAAOSwYRJhQsEA/s-l225//For-Cisco-SFP-10G-T-Ubiquiti-UF-RJ45-10G-Transceiv.jpg)
For Cisco SFP-10G-T, Ubiquiti UF-RJ45-10G Transceiver, SFP+ to RJ45 10GBase-T
$45.99
![GENUINE Cisco SFP-10G-SR V03 SFP+ GBIC Transceiver Module 10-2415-03 picture](/store/img/tAkAAOSwdENkHItI/s-l225//GENUINE-Cisco-SFP-10G-SR-V03-SFP-GBIC-Transceiver-.jpg)
GENUINE Cisco SFP-10G-SR V03 SFP+ GBIC Transceiver Module 10-2415-03
$6.80
![HP 10Gb SR SFP+ 10GBASE-SR 455885-001 10Gigabit Ethernet Transceiver 456096-001 picture](/store/img/5v0AAOSw9TVl-IVm/s-l225//HP-10Gb-SR-SFP-10GBASE-SR-455885-001-10Gigabit-Eth.jpg)
HP 10Gb SR SFP+ 10GBASE-SR 455885-001 10Gigabit Ethernet Transceiver 456096-001
$6.99
![Cisco SFP-10G-LR 10-2457-02 10GBASE-LR SFP+ Optical Transceiver picture](/store/img/WrUAAOSwHslmlWpG/s-l225//Cisco-SFP-10G-LR-10-2457-02-10GBASE-LR-SFP-Optical.jpg)
Cisco SFP-10G-LR 10-2457-02 10GBASE-LR SFP+ Optical Transceiver
$25.00
![🔥🔥🔥SFP-10G-SR V03 Original CISCO 10-2415-03 850nm 10GB SFP+ Multi Module🔥🔥 picture](/store/img/E-AAAOSwc1hiq1ol/s-l225//-SFP-10G-SR-V03-Original-CISCO-10-2415-03-850nm-10.jpg)
🔥🔥🔥SFP-10G-SR V03 Original CISCO 10-2415-03 850nm 10GB SFP+ Multi Module🔥🔥
$6.80
![New Sealed Cisco SFP-10G-LR 10GBASE-LR SFP Plug-in Transceiver Module picture](/store/img/~FsAAOSwqcFl7xTR/s-l225//New-Sealed-Cisco-SFP-10G-LR-10GBASE-LR-SFP-Plug-in.jpg)
New Sealed Cisco SFP-10G-LR 10GBASE-LR SFP Plug-in Transceiver Module
$15.00
![Brand New Cisco GLC-LH-SMD 1000BASE-LX/LH SFP Module 1310nm 10km SMF LC picture](/store/img/aIgAAOSwXWNi1sm1/s-l225//Brand-New-Cisco-GLC-LH-SMD-1000BASE-LX-LH-SFP-Modu.jpg)
Brand New Cisco GLC-LH-SMD 1000BASE-LX/LH SFP Module 1310nm 10km SMF LC
$20.99