After you modify the config file you have to open a terminal and run Lilo.
It sounds like you have not done that yet.
sakiZ
I have changed lilo.conf, but the new config does not show in my LILO boot menu.
Here is the output of lilo -v -t. It shows the newly added kernel "/boot/vmlinuz-2.6.8-2-386", but this does not appear at boot time. I boot from hda, so the error about hdc should not be of importance, or does this error prevent LILO from actually writing the boot sector?
I hope somebody knows what is going on.
LILO version 22.6.1 (test mode), Copyright (C) 1992-1998 Werner Almesberger
Development beyond version 21 Copyright (C) 1999-2004 John Coffman
Released 17-Nov-2004, and compiled at 20:01:15 on Sep 29 2005
Debian GNU/Linux
Reading boot sector from /dev/hda6
Warning: Kernel & BIOS return differing head/sector geometries for device 0x81
Kernel: 59560 cylinders, 16 heads, 63 sectors
BIOS: 1024 cylinders, 255 heads, 63 sectors
Using BITMAP secondary loader
Calling map_insert_data
Mapping bitmap file /usr/share/lilo/contrib/debian.bmp
Calling map_insert_file
Boot image: /boot/vmlinuz -> vmlinuz-2.4.26
Mapping RAM disk /boot/initrd.img -> initrd.img-2.4.26
Added Linux
Boot image: /boot/vmlinuz-2.4.26
Mapping RAM disk /boot/initrd.img-2.4.26
Added Linux(2.4)-1
Boot image: /boot/vmlinuz-2.6.5
Mapping RAM disk /boot/initrd.img-2.6.5
Added Linux(2.6)-2 *
Boot image: /boot/vmlinuz-2.6.8-2-386
Mapping RAM disk /boot/initrd.img-2.6.8-2-386
Added Linux(2.6.16)
Boot other: /dev/hdc1, on /dev/hdc, loader CHAIN
Added Windows(hdc1)
Boot other: /dev/hdc2, on /dev/hdc, loader CHAIN
Fatal: First sector of /dev/hdc2 doesn't have a valid boot signature
Thanks,
nibl
After you modify the config file you have to open a terminal and run Lilo.
It sounds like you have not done that yet.
sakiZ
I have run /sbin/lilo numerous times without the changes taking effect at boot time.
Call in the reinforcements.
sakiZ
it seems like you are putting lilo in hda6 which might be too far from the beginning of the disk for the bois to handle.
where did the original lilo get installed?
have you tried mbr on hda? or would that mess things upp,
Boot other: /dev/hdc2, on /dev/hdc, loader CHAIN
Fatal: First sector of /dev/hdc2 doesn't have a valid boot signature
I do not know any thing about lilo but if you are trying to add hdc2 , likely till you fix the boot signature there will be no success. The program is not dumb enough to add a non bootable partition, ie: no valid boot signature, and may not modify if there is any errors any where.
I could be way off as my linux knowledge is poor yet.
I just noticed this in your message output.Warning: Kernel & BIOS return differing head/sector geometries for device 0x81
This may be your clue.
sakiZ
Dell X1018 X-Series Smart Managed Switches 16-Port Gigabit 2-Port SFP Switch
$42.00
Cisco Catalyst WS-C2960X-24PS-L 24 Port Managed Gigabit Ethernet Network Switch
$59.99
Cisco Catalyst WS-C3650-24PS-L 24-Port Gigabit Ethernet Network Switch TESTED
$49.99
Dell PowerConnect 6224 Rackmount 24-Port Gigabit Managed Ethernet Network Switch
$31.99
TP-Link Metal 8-Port Gigabit Ethernet Switch Fanless Unmanaged L2+ TL-SG108(UN)
$15.00
TP-LINK TL-SG108 8-Port Switch 10/100Mbps Switch
$10.00
TP-LINK TL-SF1005D 5-Port 10/100Mbps Desktop Switch
$8.99
NETGEAR GS305E 5-Port Gigabit Ethernet SOHO Plus Switch
$5.99
Cisco Nexus 9300 48-Port 25GbE SFP 6x100GbE QSFP Switch P/N: N9K-C93180YC-EX
$499.99
Cisco Small business SG300-28P Managed 28 Port Gigabit Ethernet Switch
$67.95