Page 2 of 2 FirstFirst 12
Results 11 to 18 of 18

Thread: My Digitalcamera images?

  1. #11
    Senior Member registered user
    Join Date
    Nov 2002
    Location
    Long Island, NY, USA
    Posts
    1,256
    cat /proc/scsi/scsi says:

    Code:
    Attached devices:
    and nothing more!

    Neither can I get gphoto2 or gtkam to detect any camera....

    HELP!!!

    Frustrated,
    AJG

  2. #12
    Senior Member registered user
    Join Date
    Dec 2004
    Location
    Dublin, OH
    Posts
    342

    Nothing?????

    That command should show you all your scsi drives/devices not just your camera.

    Do your CDRom Drives show up?

    Something is way off here.

    sakiZ

  3. #13
    Senior Member registered user
    Join Date
    Jan 2006
    Posts
    135

    USB Camera

    " I: If#= 0 Alt= 0 #EPs= 3 Cls=06(still) Sub=01 Prot=01 Driver=(none) "

    Hmmm ...

    And nothing in /proc/scsi/scsi .

    I've been following this thread and it seems more and more likely a firmware/bios/hardware issue.

    If all the BIOS USB settings are enabled, I suggest that you check the cabliing to the on board USB header. I've seen systems shipped with the data wires interchanged to cross between two case connectors. What happens is that the initial exchange of information is passed over the voltage wires, so the system knows that something has connected and what it is, but the data lines never complete negotiation.

    But it is still curious that your hubs have not been registered. I would doublecheck the bios settings first.

    Have you ever used these USB ports before and found then working?

  4. #14
    Senior Member registered user
    Join Date
    Nov 2002
    Location
    Long Island, NY, USA
    Posts
    1,256
    OK, you're going to want to move all the sensitive and impressionable types out of the room for a second as I have to use some fowl language.

    Ready? Here goes nothing! My response:

    Well, there's the rub. I have used this camera/cable/port combo in (watch out, here it comes) WinDoze (sorry) without a hitch. There, I said it. Are you happy you made me admit to using the unNamableOS (sorry)? However, this is the only thing I need WIMxP (again, sorry) for, so I'd rather not have to use it at all....

    BTW, I hope I have nothing to worry about regarding the profanity above. I'm sure the words in bold will be editted out by the censors (but, of course, you can't see those words, so you don't know what I'm talking about)!

    TIA,
    AJG

  5. #15
    Senior Member registered user
    Join Date
    Dec 2004
    Location
    Dublin, OH
    Posts
    342

    Happy You HAVE to use Windoze?

    Well, no I'm not happy you have to go back to using an aging (over 5 years old) proprietary, virus magnet.

    But you gotta do what you gotta do.

    Good luck.

    sakiZ

  6. #16
    Senior Member registered user
    Join Date
    Jan 2006
    Posts
    135

    USB Camera

    For our information, what make and model of computer is this, and any other particulars you know or care to mention.

    The output of the command: lspci -vvv would be appreciated.

    I'm sorry that we could not help you, but, some of these problems are intractable in this proprietary world.

  7. #17
    Senior Member registered user
    Join Date
    Nov 2002
    Location
    Long Island, NY, USA
    Posts
    1,256
    Thanx for all your help! Don't sweat it if you can't figure out my problem. Its really the Mrs that uses this box and camera combo in WimpDoze. I use my Dell GX270 PIV cluster at school. Anyway, I've gotten SO MUCH out of using KNOPPIX and you guys have HELPED ME SO MUCH over the years, that this is just one minor blip on the radar screen as far as I'm concerned! I'm such a KNOPPIX maven now that if I can't get the camera to work with KNOPPIX, I just won't use it, that's all.... I just won't touch WimpDoze anymore. Any time I do, its such a headache!

    OK, I have KNOPPIX 4.0.2CD installed to hda2 (dual boot as the better half must use WIMxP). The box is a Dell Dimension 4100 PIII 866Mhz with 128MB RAM and 20GB hdd and an 8x cdr drive. Could this be like a winModem problem? In other words, my USB hardware is designed to work only with WimpDoze?

    Code:
    lspci -vvv > temp.txt
    returns:

    0000:00:00.0 Host bridge: Intel Corp. 82815 815 Chipset Host Bridge and Memory Controller Hub (rev 02)
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
    Latency: 0
    Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
    Capabilities: [88] #09 [f104]
    Capabilities: [a0] AGP version 2.0
    Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
    Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW- Rate=x4

    0000:00:01.0 PCI bridge: Intel Corp. 82815 815 Chipset AGP Bridge (rev 02) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 64
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: fc900000-fe9fffff
    Prefetchable memory behind bridge: f0600000-f46fffff
    BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-

    0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 02) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
    I/O behind bridge: 0000d000-0000dfff
    Memory behind bridge: fea00000-feafffff
    Prefetchable memory behind bridge: f4700000-f47fffff
    BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-

    0000:00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 02)
    Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0

    0000:00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 02) (prog-if 80 [Master])
    Subsystem: Intel Corp.: Unknown device 4541
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Region 4: I/O ports at ffa0 [size=16]

    0000:00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #1) (rev 02) (prog-if 00 [UHCI])
    Subsystem: Intel Corp.: Unknown device 4541
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin D routed to IRQ 10
    Region 4: I/O ports at ef80 [size=32]

    0000:00:1f.3 SMBus: Intel Corp. 82801BA/BAM SMBus (rev 02)
    Subsystem: Intel Corp.: Unknown device 4541
    Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin B routed to IRQ 9
    Region 4: I/O ports at efa0 [size=16]

    0000:01:00.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 64/Model 64 Pro] (rev 15) (prog-if 00 [VGA])
    Subsystem: nVidia Corporation: Unknown device 0001
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 248 (1250ns min, 250ns max)
    Interrupt: pin A routed to IRQ 11
    Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
    Region 1: Memory at f2000000 (32-bit, prefetchable) [size=32M]
    Expansion ROM at fe9f0000 [disabled] [size=64K]
    Capabilities: [60] Power Management version 1
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [44] AGP version 2.0
    Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
    Command: RQ=32 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW- Rate=x4

    0000:02:09.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 7
    Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC Management NIC
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 0x08 (32 bytes)
    Interrupt: pin A routed to IRQ 3
    Region 0: I/O ports at dc00 [size=128]
    Region 1: Memory at feaffc00 (32-bit, non-prefetchable) [size=128]
    Expansion ROM at feac0000 [disabled] [size=128K]
    Capabilities: [dc] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=2 PME-

    0000:02:0c.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 09)
    Subsystem: Ensoniq Creative Sound Blaster AudioPCI64V, AudioPCI128
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort+ <MAbort+ >SERR- <PERR-
    Latency: 64 (3000ns min, 32000ns max)
    Interrupt: pin A routed to IRQ 9
    Region 0: I/O ports at df00 [size=64]
    Capabilities: [dc] Power Management version 2
    Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    HTH,
    AJG

  8. #18
    Senior Member registered user
    Join Date
    Jan 2006
    Posts
    135

    Dell computer and USB Camera

    Your computer uses dell specific oem devices. This information should be forwarded to www.linux-usb.org that the device information may be included in future driver releases. The line below from your output is typical of this (Unknown device) and there are several.

    0000:00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #1) (rev 02) (prog-if 00 [UHCI])
    Subsystem: Intel Corp.: Unknown device 4541

Page 2 of 2 FirstFirst 12

Similar Threads

  1. Burning DVD images using Knoppix!
    By DelNorte in forum General Support
    Replies: 1
    Last Post: 03-22-2005, 07:27 AM
  2. no boot floppy images any more? (3.6)
    By ThomasX in forum General Support
    Replies: 6
    Last Post: 01-25-2005, 01:32 PM
  3. cmg Compressed Application Images
    By probono in forum Klik
    Replies: 5
    Last Post: 01-15-2005, 11:51 PM
  4. How can I copy images .mdf .mds!!
    By zlibre in forum General Support
    Replies: 2
    Last Post: 10-08-2004, 03:00 AM
  5. Using apt-get & apt-cdrom with Debian ISO images
    By HomerCube in forum General Support
    Replies: 0
    Last Post: 09-29-2004, 03:09 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


Dell PowerEdge R720 Server - 2x8c CPU,256Gb RAM, 128Gb SSD/3x600Gb SAS, Proxmox picture

Dell PowerEdge R720 Server - 2x8c CPU,256Gb RAM, 128Gb SSD/3x600Gb SAS, Proxmox

$340.00



Dell PowerEdge M610 Blade Server E5620@2.2GHZ (6x)8GB RAM (2x)146GB 15K SAS HDD picture

Dell PowerEdge M610 Blade Server E5620@2.2GHZ (6x)8GB RAM (2x)146GB 15K SAS HDD

$75.00



Supermicro 4U 36 Bay Storage Server 2.4Ghz 8-C 128GB 1x1280W Rails TrueNAS ZFS picture

Supermicro 4U 36 Bay Storage Server 2.4Ghz 8-C 128GB 1x1280W Rails TrueNAS ZFS

$721.06



H261-Z61 2U 24SFF AMD Server 8x EPYC 7551 256-Cores 256GB RAM 8x25G NIC 2x2200W picture

H261-Z61 2U 24SFF AMD Server 8x EPYC 7551 256-Cores 256GB RAM 8x25G NIC 2x2200W

$2512.18



Dell PowerEdge R720XD Xeon E5-2680 V2 2.8GHz 20 Cores 256GB RAM 12x4TB picture

Dell PowerEdge R720XD Xeon E5-2680 V2 2.8GHz 20 Cores 256GB RAM 12x4TB

$510.00



DELL PowerEdge R730 Server 2x E5-2690v3 2.6GHz =24 Cores 32GB H730 4xRJ45 picture

DELL PowerEdge R730 Server 2x E5-2690v3 2.6GHz =24 Cores 32GB H730 4xRJ45

$275.00



Dell PowerEdge R730XD 28 Core Server 2X Xeon E5-2680 V4 H730 128GB RAM No HDD picture

Dell PowerEdge R730XD 28 Core Server 2X Xeon E5-2680 V4 H730 128GB RAM No HDD

$389.99



Dell PowerEdge R620 Server 2x Xeon  E5-2620 @ 2.0GHz 64GB RAM NO HDDs picture

Dell PowerEdge R620 Server 2x Xeon E5-2620 @ 2.0GHz 64GB RAM NO HDDs

$108.96



Dell PowerEdge R820 Server 4x E5-4620 2.2GHz 32-Core Total 256GB 0HD 2x 1100w  picture

Dell PowerEdge R820 Server 4x E5-4620 2.2GHz 32-Core Total 256GB 0HD 2x 1100w

$315.00



Dell PowerEdge R430 3.5 1U 2x E5-2690 v3 2.6ghz 24-Cores 256gb 4x Trays 2x 550w picture

Dell PowerEdge R430 3.5 1U 2x E5-2690 v3 2.6ghz 24-Cores 256gb 4x Trays 2x 550w

$289.99