I have the same problem and have been looking around for the answer. I will post it when I fix the problem. I am going on an all out search for the answer.
I am a very new user to KNOPPIX and am seeking help. One of the latest topics on the forum about "can't find KNOPPIX filesystem" is also happening to me. I use KNOPPIX daily and have it installed on hard drives and also run it daily from a CD. Over the past 6 months I have never seen this error until I started building PC's with the Intel DG965RY motherboard. I believe this problem is some type of conflict with the Intel chipset. I have seen this problem discussed on the Intel forum and there are several Intel motherboards having the same problem. An Intel rep suggested a BIOS update for Linux but that didn't help. I am hoping you have some suggestions. We are going to check and possibly reburn the CD but I have my doubts about that helping. I have built nearly 150 PC's in the last 6 months using the same CD's, versions 3.7 and 5.0. We also tried the latest 5.1.1. All versions give the same error message.
I have the same problem and have been looking around for the answer. I will post it when I fix the problem. I am going on an all out search for the answer.
with your latest new Intel board, did you also change cd-drive type ?
that's the more important piece of info needed.
if not, then def something with the board
or cheatcodes... after 150 systems, have you had time or need to play with various codes ?
I've not, so I can't help apart from nodma might help, without non-std ide interface drivers
code for use plain ide ? atapicd for one
can you get a dos screen for a lspci ?
All 150 systems are identical except for the motherboard. I have tried some codes like nodma but they don't help.
After the error occurs I am stuck in the KNOPPIX shell with limited commands.
did you try disabling any advanced hardware detection and try to boot .. maybe booting the expert mode might help
ok, same deal but slightly different tack
all systems are identical
apart from ....... serial numbers on the cd-rom drives
might be the same type of drive
but won't be the same drive (unless you are building off a test bench)
can you swap the drive and re-test ?
might be a dud cd-drive
me mums dvd half booted the cd
got the splash screen, and most of the startup
but no desktop
then i found it wouldn't play a dvd either
new drive
very finicky when going kaput
Yes, I have tried the Expert code along with different CD drives. I have seen this issue discussed elsewhere and I am leaning towards the problem being the Intel chipset. I guess if that is truly where the problem lies then either Linux or Intel will find a fix.
I was getting the knoppix file system error when trying to use a DVD burner as my primary. I changed to a normal DVD drive, and it worked. That was the only thing I changed. Hope that is all it takes for everyone else.
NEW Sealed Cisco SFP-10G-LR 10GBASE-LR SFP+ 1310nm 10km *US Shipping*
$18.00
New HP HPE Aruba J4858D 1G SFP LC SX 850nm 500m MMF XCVR Transceiver Module
$28.49
For Cisco SFP-10G-T, Ubiquiti UF-RJ45-10G Transceiver, SFP+ to RJ45 10GBase-T
$45.99
New Cisco SFP-25G-SR-S 25G SFP28 25GBASE-SR 850nm 300m LC MMF Transceiver Module
$51.30
GENUINE Cisco SFP-10G-SR V03 SFP+ GBIC Transceiver Module 10-2415-03
$6.80
🔥🔥🔥 CISCO SFP-10G-SR V03 10-2415-03 850nm 10GBASE-SR SFP+ Multi Module 🔥🔥🔥
$6.80
Cisco GLC-LH-SMD Transceiver Module SFP 10-2625-01
$14.25
HP 10Gb SR SFP+ 10GBASE-SR 455885-001 10Gigabit Ethernet Transceiver 456096-001
$6.99
New Precision DWDM SFP+ 10G 80km Tunable Transceiver 50GHz C-Temp DWDM-SFP10G-C
$90.00
Dell X1018 X-Series Smart Managed Switches 16-Port Gigabit 2-Port SFP Switch
$42.00