post the output of ifconfig
I have a suspicion![]()
Just installed knoppix 5.1.1 on my machine, however I was unable to get it to recognise my builtin Ethernet port.
Motherboard is Asus P4P800 with Yukon Gigabte 10/100/1000 chipset. The problem is that knoppix 2.4.19 kernel loads
the sk98lin module which is deprecated and has been replaced by the skge module.
I tried removing and installing kernel modules, but could not fix this, so I have had to reload knoppix 5.0.1
Used commands:
rmmod sk98lin modprobe skge
I could ping my own card with a static address, but not my router? This is strange because the default gateway was showing
but I could not ping the router. Pinging a WAN address i.e. ping www.google.co.uk also failed, as I cannot reach the router.
The contents of resolv.conf were fine, just dont know what was wrong.
Previous versions of knoppix and 5.01 work fine.
Heres the output from knoppix 5.01:
anc@orac:~$ lspci -vv | grep Ethernet
0000:02:05.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8001 Gigabit Ethernet Controller (Asus)
anc@orac:~$ dmesg | grep eth
skge eth0: addr 00:0e:a6:8c:f3:16
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
skge eth0: enabling interface
ADDRCONF(NETDEV_UP): eth0: link is not ready
skge eth0: Link is up at 100 Mbps, full duplex, flow control tx and rx
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
If there is a way to get my ethernet working with knoppix 5.1.1 I wil try it. Using the live cd of knoppix 5.1.1 also
I also know that the kdesu command is not working but using commands from the route terminal solve this.
Thanks in advance for any help.
post the output of ifconfig
I have a suspicion![]()
This might be the same problem that I had with Knoppix 5.1.1 - look in the Networking topic - 5.1.1 Network problem with Gigabyte GA-965P-DQ6 + workround
for the way that I got it to work.
(The gigabyte motherboard has the same ethernet chip as yours)
Sorry my mistake.
When I viewed the boot messages with dmesg, knoppix 5.11 configures my Firewire IEEE1394 interface as eth0, and my Yukon
network adapter as eth1.
Networking is simply a matter of configuring the correct interface, in my case eth1. Previous versions of knoppix and some other linux distros, enumerate eth0 as my ethernet card and eth1 as the firewire interface. This is something I will look out for in future.
G.SKILL Ripjaws X DDR3 memory kit (1600 Default) (1866 2133 XMP) 2pcs 2X4GB/8GB
$16.00
Crucial DDR3L 16GB 1600 2x 8GB PC3-12800 Laptop SODIMM Memory RAM PC3 16G DDR3
$44.85
30 Pin & 72 Pin SIMM Memory, Bulk Lot Of 59 Total
$80.00
Samsung 8GB - 1Rx8 - PC4-2666V Desktop RAM Memory | M378A1K43CB2-CTD
$9.99
A-Tech 8GB DDR3 1600 PC3-12800 Laptop SODIMM 204-Pin Memory RAM PC3L DDR3L 1x 8G
$13.99
Samsung 16GB DDR4 3200MHz PC4-25600 260-Pin Laptop Memory M471A2G43BB2-CWE - New
$42.50
HyperX FURY DDR3 8GB 16GB 32GB 1600 MHz PC3-12800 Desktop RAM Memory DIMM 240pin
$23.95
USB Flash Drive Memory Stick Pendrive Thumb Drive 4GB, 8GB, 32GB, 64GB 128GB LOT
$223.42
A-Tech 128GB 4x 32GB 4Rx4 PC3-14900 DDR3 1866 MHz ECC LRDIMM Server Memory RAM
$95.96
A-Tech 128GB 4x 32GB 2Rx4 PC4-19200R DDR4 2400 ECC REG RDIMM Server Memory RAM
$191.96