-
Networking not starting at boot up
Hi All
During boot up, the configs.tbz is read from floppy,
Mesg 'setting up networking' appears, followed by '* /etc/network/options is deprecated...'
I can not access my network until I go through Knoppix > Network/Internet > network card configuration
All my previous settings appear and networking is started up and everything works. Any ideas?
My options file reads:
ip_forward=no
spoofprotect=yes
synccookies=no
I'm running 5.1.1 Live CD
I have spent ages trawling through the forum & how-tos
All suggestions greatly appreciated.
-
Senior Member
registered user
If youre running the live cd then yes you will have to setup your network each time.
If you have done a permanent HD install (not recommended for beginners) then you must install as either a Debian system, or beginner system, these will remember your configuration settings. The CD type install behaes exactly like the cd.
-
manual setup required??
I don't understand this:
Originally Posted by
hal8000
If youre running the live cd then yes you will have to setup your network each time.
When booting knoppix 4.0, I don't have to setup anything....it works immediately. But 5.1.1 does require setup.
Is this by design, or is this a problem I can fix?
-
Junior Member
registered user
Hi, I'm also having problems with my knoppix load not auto-starting my network now. I've done the HDD install and never had a problem with the network card starting on start-up until recently. I had some ethernet cable problems and swapped out a faulty cable and now my network card doesn't auto-start? Any idea why? I never had this problem before? Now I have to go into the network config under the knoppix menu and run network card configuration to get on my network. I thought it had an option to autostart but I'm not seeing it anymore? Thanks for any/all ideas and help.
Here's my version.
Code:
root@nuxbox:/home/james# cat /proc/version
Linux version 2.6.12 (root@Knoppix) (gcc-Version 3.3.6 (Debian 1:3.3.6-7)) #2 SMP Tue Aug 9 23:20:52 CEST 2005
-
This is what my /etc/network/interfaces looks like
auto lo wlan0
iface lo inet loopback
allow-hotplug wlan0
iface wlan0 inet dhcp
wireless_mode managed
wireless_rate 54M auto
wireless_channel 11
wireless_essid XXXXXXXX
wireless_key XXXXXXXXXXXXXX
post-up route add default gateway 192.168.0.1
It now starts everytime!!
Similar Threads
-
By darrmik in forum Hardware & Booting
Replies: 7
Last Post: 01-15-2009, 05:03 PM
-
By jwh7 in forum General Support
Replies: 1
Last Post: 10-13-2004, 11:06 PM
-
By lothario in forum Hdd Install / Debian / Apt
Replies: 9
Last Post: 08-17-2004, 11:57 PM
-
By c123 in forum Hdd Install / Debian / Apt
Replies: 5
Last Post: 03-27-2004, 07:08 AM
-
By bongski55 in forum General Support
Replies: 1
Last Post: 05-07-2003, 01:19 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
NEW Sealed Cisco SFP-10G-LR 10GBASE-LR SFP+ 1310nm 10km *US Shipping*
$18.00
New HP HPE Aruba J4858D 1G SFP LC SX 850nm 500m MMF XCVR Transceiver Module
$28.49
New Cisco SFP-25G-SR-S 25G SFP28 25GBASE-SR 850nm 300m LC MMF Transceiver Module
$51.30
For Cisco SFP-10G-T, Ubiquiti UF-RJ45-10G Transceiver, SFP+ to RJ45 10GBase-T
$45.99
GENUINE Cisco SFP-10G-SR V03 SFP+ GBIC Transceiver Module 10-2415-03
$6.80
🔥🔥🔥 CISCO SFP-10G-SR V03 10-2415-03 850nm 10GBASE-SR SFP+ Multi Module 🔥🔥🔥
$6.80
Cisco GLC-LH-SMD Transceiver Module SFP 10-2625-01
$14.25
Dell 10GBase SPF + Optical Transceiver Module - XYD50
$10.00
New Precision DWDM SFP+ 10G 80km Tunable Transceiver 50GHz C-Temp DWDM-SFP10G-C
$90.00
New Cisco GLC-TE 1G SFP Copper RJ45 100m 1000BASE-T Transceiver Module
$22.32