-
XFree86 screen configuration
My first post here.
After my HDD install everything worked fine but the resolution set by Knoppix was far too high for me to see anything properly on my 14" CTX monitor.
I ran the kXConfig in my KDE desktop ("Advanced XFree86 Configuration") It displayed the Monitor settings, keyboard settings and pointer settings correctly to what Knoppix had correctly detected and the Video card was claimed to be of type "Generic Versa". I tried to change the screen resolution to 800x600, saved and restarted X. However, the resolution I ended up with was very low, I think 640x480 and the clock wouldn't fit on the taskbar! After this point it seemed to be stuck on this resolution and whatever resolutions or colour depths I tried it always went to 640x480 whenever I restarted X. I think this might be to do with the generic graphics card driver.
I got the graphics card second hand but it says "S3 Trio64 V2/DX" on one of the chips so I tried the "S3 Trio 3D/2X" and "S3 Trio3D" and "Generic s3virge" drivers, none of which worked and X refused to start.
I booted using the CD-ROM again and I overwrote the XF86Config and XF86Config-4 files on the hard disk with the ones that Knoppix generated so I was back where I started as I'd rather have the very high resolution that the very low one that the manual config keeps forcing.
Is the problem simply that my graphics card is not supported? And if so what setup is Knoppix using to achieve a very high resolution (about 1024x76 and can I use the same settings but modify them slightly to 800x600?
Here are dumps of the appropriate parts of the config files generated by Knoppix...
XF86Config==================
Code:
# Auto-generated by mkxf86config
Section "Monitor"
Identifier "Monitor0"
VendorName "CTX"
ModelName "CTX1451"
# HorizSync 28.0 - 78.0 # Warning: This may fry very old Monitors
HorizSync 28.0 - 96.0 # Warning: This may fry old Monitors
VertRefresh 50.0 - 76.0 # Very conservative. May flicker.
# These are the DDC-probed settings reported by your monitor.
# 1280x1024, 75.0Hz; hfreq=79.98, vfreq=75.03
ModeLine "1280x1024" 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync
# 1024x768, 60.0Hz; hfreq=48.36, vfreq=60.00
ModeLine "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
# 640x480, 75.0Hz; hfreq=37.50, vfreq=75.00
ModeLine "640x480" 31.50 640 656 720 840 480 481 484 500 -hsync -vsync
EndSection
Section "Device"
Identifier "My Video Card"
VendorName "Unknown"
BoardName "Unknown"
# TextClockFreq 22.175
EndSection
Section "Device"
Identifier "fbdev"
VendorName "Unknown"
BoardName "Unknown"
EndSection
# Standard Server
Section "Screen"
Driver "svga"
Device "My Video Card"
Monitor "Monitor0"
Subsection "Display"
Modes "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
EndSection
# Accel. Server(s)
Section "Screen"
Driver "accel"
Device "My Video Card"
Monitor "Monitor0"
Subsection "Display"
Modes "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
EndSection
# Fallback
Section "Screen"
Driver "vga16"
Device "My Video Card"
Monitor "Monitor0"
Subsection "Display"
Modes "1024x768" "800x600" "640x480"
EndSubsection
EndSection
Section "Screen"
Driver "fbdev"
Device "fbdev"
Monitor "Monitor0"
SubSection "Display"
Depth 32
Modes "default"
EndSubSection
SubSection "Display"
Depth 24
Modes "default"
EndSubSection
SubSection "Display"
Depth 16
Modes "default"
EndSubSection
SubSection "Display"
Depth 15
Modes "default"
EndSubSection
SubSection "Display"
Depth 8
Modes "default"
EndSubSection
EndSection
XF86Config-4================
Code:
# Auto-generated by KNOPPIX mkxf86config
Section "Monitor"
Identifier "Monitor0"
Option "DPMS" "true"
VendorName "CTX"
ModelName "CTX1451"
# HorizSync 28.0 - 78.0 # Warning: This may fry very old Monitors
HorizSync 28.0 - 96.0 # Warning: This may fry old Monitors
VertRefresh 50.0 - 76.0 # Very conservative. May flicker.
# These are the DDC-probed settings reported by your monitor.
# 1280x1024, 75.0Hz; hfreq=79.98, vfreq=75.03
ModeLine "1280x1024" 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync
# 1024x768, 60.0Hz; hfreq=48.36, vfreq=60.00
ModeLine "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
# 640x480, 75.0Hz; hfreq=37.50, vfreq=75.00
ModeLine "640x480" 31.50 640 656 720 840 480 481 484 500 -hsync -vsync
EndSection
Section "Device"
### Available Driver options are:-
# sw_cursor is needed for some ati and radeon cards
#Option "sw_cursor"
#Option "hw_cursor"
#Option "NoAccel"
#Option "ShowCache"
#Option "ShadowFB"
#Option "UseFBDev"
#Option "Rotate"
Identifier "Card0"
# The following line is auto-generated by KNOPPIX mkxf86config
Driver "vesa"
VendorName "All"
BoardName "All"
# BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultColorDepth 16
SubSection "Display"
Depth 1
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 4
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 15
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 32
Modes "1024x768" "800x600" "640x480"
EndSubSection
EndSection
Section "DRI"
Mode 0666
EndSection
Sorry about the length of this post but I'm trying to give you as much information as I can.
Thanks for your time, and please be gentle with me, I'm a newbie
tola ^/.
Similar Threads
-
By beige_matchbox in forum MS Windows & New to Linux
Replies: 2
Last Post: 04-15-2005, 05:45 PM
-
By RE Dude in forum The Lounge
Replies: 1
Last Post: 11-01-2003, 04:10 PM
-
Replies: 5
Last Post: 05-03-2003, 07:02 PM
-
By xound in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 04-23-2003, 08:29 AM
-
By good_karma69 in forum General Support
Replies: 0
Last Post: 03-09-2003, 01:20 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Extron RGB-160XI Analog Computer Video 60-378-01
$187.06
The analog thing modern open source, educational, low-cost analog computer
$800.00
Vintage 1960s Donner Model 3000 Analog Computer ~ MUSEUM PIECE Extremely Rare
$4000.00
Apple Macintosh SE/30 M5119 Computer 8MB RAM Recapped Working *See Description*
$475.00
NEW Aquarius+ Computer Signature Edition - 8Bit Retro System
$229.00
Landen Computer. Circa 1898. the Rapid Computer Company. With Original Case.
$425.00
Burr Brown Analog Computer parts Circuit boards w Helipot Potentiometers 1631a
$85.00
Apple IIc Analog Board NOS - 661-0265
$74.00
Two (2) vintage The Analog Computing Pocket Reference Cards, 1985
$19.99
ACASIS PCIE Capture Card HDMI 1.4 1080P60HZ PCIE 2.0 X4 20Gbps for Video Capture
$248.99