I have no additional help to offer that you seem ready to accept.Originally Posted by Fog_Watch
I thought I would use Knoppix to boot my old Proliant DL380. The Knoppix (5.1.1) is able to boot an ordinary white box, but not the Proliant. The kernel loads and then very early in the hardware detection it returns the error:
insmod: error inserting '/cdrom/KNOPPIX/modules/cloop.ko': -
The problem is very similar to this, only I can't see how it can be a problem with the disk when it can be used to boot other computers. Any clues?
Thanks for reading.
Regards
Fog_Watch.
PS. This beast usually needs a cpqarray module loaded. I don't know if that is an issue.
I have no additional help to offer that you seem ready to accept.Originally Posted by Fog_Watch
Fog_Watch
You may very well have found the problem and answer, but you seem to refuse to accept the solution. Many disks that are burned at higher speeds may simply not work well in ALL optical drives. This may be the issue you encountered, especially with older hardware. Higher burn speeds seem to create some drive compatibility issues. It is encountered quite often with Audio CDs that don't play well, or at all in some CD players, but play well in others. Burning the disc at a slow speed usually resolves the compatability issue. Like it or not, it's a common problem.
Another issue could be that the drive/hardware is unable to work well with DMA acceleration or without it. The "knoppix nodma" cheatcode may help by disabling it, or "knoppix dma" to enable DMA acceleration. I'm not sure if 5.1.1 is enabled or disabled by default. You can try one or the other to see if that solves your problem.
I accept the possibility of writing speed being the cause of the problem. I, however, found a different solution.Originally Posted by ckamin
This did not alter the errorOriginally Posted by ckamin
The solution was to use KNOPPIX_V4.0.2. This booted the machine fine. A small problem was it not having lvm v2, but I get this off a floppy (after modprobe dm_mod) to solve that problem. This solution did not surprise me as a Gentoo 2007 disk does not boot the machine but a 2006 does.
Harry Kuhman and ckamin, thank you both for your replies.
Regards
Fog_Watch
In many ways I find 4.02 to be superior to any of the 5.x discs. But the fact that a different disc, even a 4.02 one, does boot just reinforces the belief that the failing disc was likely made at high speed and that another one burnt at slower speed would likely boot as well. Of course, there can be other differences such as media quality, but speed of burn is the most common issue that we see here.Originally Posted by Fog_Watch
---
Verifying of md5 checksum and burning a CD at slow speed are important.
I experienced the same error while booting a Knoppix ISO within Virtualbox. The burning speed suggestion isn't very helpful on this issue now. Any ideas?
Thanks for any help,
falken
Vintage Keytronic PC/AT VT Switch FCC ID:CIG8AVE03435 TESTED WORKING
$30.00
NMB KEYBOARD RT2258TW NMB PS/2 BEIGE 121944-101 REV A VINTAGE NEW OLD STOCK
$25.99
Vintage Compaq Presario 5000 Celeron 600 WIN 98 66MHz 255MB RAM 80GB HDD
$75.00
Vintage Inter Act Roller ball computer mouse - **WORKING*
$9.88
Lot Of 5 - Vintage IBM style 80 Column Punch Cards - Kelly 5081, Pink Print Band
$5.00
Tandy 200 Vintage Portable Computer 26-3860 w/ Manuals
$189.99
Vintage SCCS Interface Microcomputer Magazine Pair 1976 IMSAI 8080 Altair 8800
$26.00
Vintage Collectible Microsoft Windows xp Owners Manual and Software, 2002
$2.50
Vintage Atari 1040STf Computer with Mouse and Box, Minimal Testing, Pls Read
$149.99
Vintage Nan Tan KB-5161 Clicky Mechanical Alps Keyboard Blue **Arabic Key**
$130.00