-
Knoppix Commands
Hi to all the learned knoppix folk
I am at a loss at what to do next. ( I am a learner)
I have a HP Compaq Presario V5104 AMD Laptop with a Mobile Sempron Chip Set ATI Radeon Graphics card 160 Hd with 2 Gig of Memory
I have loaded the Knoppix 6 Live Cd and DVD at seperate occasions
I am trying to use the knoppix boot commands when the cd or dvd boots up
I have partitioned my laptop I have WindozeXp on 30 GiG Partition & the rest is partitioned with ext2
I would dearly love to run this Knoppix Live Cd/DvD with the toram command but it doesn't work
/init line 206 toram not found
init version 2.86
I have tried step by step the basic poor mans install.
I am sorry that doesn't work iether.
Where I am going wrong?
Help
Kind Regards
Geoff
-
Senior Member
registered user
Re: Knoppix Commands
Originally Posted by
Sologeoff
Hi to all the learned knoppix folk
I am at a loss at what to do next. ( I am a learner)
I have a HP Compaq Presario V5104 AMD Laptop with a Mobile Sempron Chip Set ATI Radeon Graphics card 160 Hd with 2 Gig of Memory
I have loaded the Knoppix 6 Live Cd and DVD at seperate occasions
I am trying to use the knoppix boot commands when the cd or dvd boots up
I have partitioned my laptop I have WindozeXp on 30 GiG Partition & the rest is partitioned with ext2
I would dearly love to run this Knoppix Live Cd/DvD with the toram command but it doesn't work
/init line 206 toram not found
init version 2.86
I have tried step by step the basic poor mans install.
I am sorry that doesn't work iether.
Where I am going wrong?
Help
Kind Regards
Geoff
Never use toram boot cheat code before on knoppix 6.
One question needs to be answered. Is it a CD or a DVD you are using?
If it is a DVD, then it makes sense since you have only 2G RAM and the DVD is around 4.5G in size.
However, if you are using CD, then it may mean that knoppix 6 no longer allow you to run toram.
Rgds,
Chip
-
toram crashed on me Compaq 5000 Knoppix 6.2. Locked up tight. 540 MB ram not enough? I dont recall the error message, but it appeared to be loading from CD to RAM, as the CD was running but no HDD activity.
-
Senior Member
registered user
wow, try to load a CD iso to 512M, short answer, NO 512M is NOT enough, the entire 700M of the CD have to reside in ram and it must have ram left to work with, q quick estimate would say 1G or more.
-
yes, on my flash installation with a few files added, its using 1.6 Gb so right, 512 isnt enough.
-
will All ubuntu commands work in knoppix?
-
Senior Member
registered user
if you are talking console commands most likely more than 90% will work, if you are uncertain try typing
to get a brief manual on the command in question.
Similar Threads
-
By HatGuy in forum General Support
Replies: 2
Last Post: 05-30-2007, 01:40 AM
-
By dan.g in forum Hardware & Booting
Replies: 0
Last Post: 03-30-2007, 09:10 PM
-
By pasi in forum Hardware & Booting
Replies: 2
Last Post: 06-07-2006, 04:02 PM
-
By section_8te in forum Hardware & Booting
Replies: 6
Last Post: 03-13-2005, 04:06 PM
-
By wingnut2292 in forum Customising & Remastering
Replies: 2
Last Post: 09-07-2004, 10:11 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Cisco GLC-FE-100LX 100BASE-LX SFP Transceiver Module
$15.59
Cisco GLC-FE-100LX-RGD 100BASE-LX SFP Transceiver Module
$17.99
Cisco w/ Green Hologram SFP-25G-SR-S 25G SFP28 SR 850nm 100m LC MMF
$68.99
Cisco Meraki MA-SFP-1GB-SX 1000BASE-SX SFP Transceiver Module
$24.99
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
SFP-10G-SR Original Cisco 10GBASE-SR SFP+ V02 Multi mode Transceiver 10-2415-02
$5.00
Brand New Cisco GLC-LH-SMD 1000BASE-LX/LH SFP Module 1310nm 10km SMF LC
$13.89
Genuine Cisco GLC-TE 30-1475-01 V01 1000BASE-T SFP COPPER RJ-45 100M TRANSCEIVER
$11.90
LOT OF 20 Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module
$89.00
10 PCS Cisco GLC-LH-SMD 10-2625-01 1310nm SFP Transceiver Module
$85.00