is that possible ? I believe in order for this to happen, the linksys must also support bridge function or the packet on the other side just won't come over(and vice versa).
Why not just 2 sub-net which would make things simpler ?
As of right now at my home I have setup knoppix as a dialup router, and I'm pretty well versed in linux routers. The issue I'm facing is that I'm fixing to move into a home I purchaced next to my parents house, and I would like to network the two houses together wirelessly. Here is the plan.
What I would like to do is have a Linksys WAP11 access point at my mom's house and use a knoppix box at my house that has a WUSB11 adapter and a regular network card and bridge eth0 and wlan0.
Here is the setup I would like:
(mom's house);
home router[2.254]------> wap11[2.253] -->
++wireless hop+++
(my house);
knoppix wifi card[2.252]--------> knoppix eth0[2.251]------> my switch--------> my wap11 for my home network[2.250]-------> my wireless laptop[2.118]
My desktop would also be plugged into my switch with the address of [2.249]
Is this possible? I would rather have everything on one subnet instead of having 192.168.3.0 network at my house and 192.168.2.0 at her house and the wifi side of my knoppix box with knoppix acting as a router between subnets. I know it wouldn't be routing because you don't route packets on the same subnet, but is there a way to do this with iptables just to bridge eth0 and wlan0? I guess I'm trying to make knoppix into a poor mans linksys WET11 Wireless bridge.
Sorry for the long post, but I figured it was best to explain the whole situation.
Thanks!
is that possible ? I believe in order for this to happen, the linksys must also support bridge function or the packet on the other side just won't come over(and vice versa).
Why not just 2 sub-net which would make things simpler ?
The linksys WAP11 supports a bridge function, but instead of using the WAP11 in bridge mode, I was going to put it in infrastructure mode and set it up in a window at my moms and put the wireless adapter on my knoppix box in a window at my house, and just have the knoppix box be a client off of the WAP11.
I just didn't want to have a seperate subnet on the eth0 side of my knoppix box. I would rather have eth0 and wlan0 be on the same subnet and have the traffic from my house to her's pass transparently through the knoppix machine.
What you are proposing is not only feasable but I am doing it, though I am not using knoppix in my bridge I am using OpenBSD, but the configuration should roughly be the same. What you are doing is turning a$700 computer into a $5.00 bridge.
in the /etc just configure the interfaces:
not as dhcp
not to a static ip but as "up"
example
hostnamexl0
#dhchp
#inet
up
then
hostnamexl11
#dhcp
#inet
up
you can also add packet filtering or have the bridge do NAT
since you want to use knoppix though and knoppix is debian based I reccomend you read the following: http://www.wlug.org.nz/WirelessEthernetBridge
take care and good luck,
Thanks for the replies!
I think I'm going to just get 2 WAP11s and call it a day. Although, I will attempt this project just for the sake of knowing how to do it.
I do however wish that a wireless bridge was $5, I would use them for everything! Unfortunatly the linksys WET11 wireless bridge is more expensive than a WAP11. So what do I do, buy a WAP11 and put it in bridge mode.
You may want to take a look at this post.
http://www.knoppix.net/forum/viewtopic.php?t=663#2561
1U Supermicro Server 10 Bay 2x Intel Xeon 3.3Ghz 8C 128GB RAM 480GB SSD 2x 10GBE
$297.00
HP ProLiant Xeon E3-1220L V2 MicroServer Gen8 2.30 GHz 16 GB RAM NO DRIVES
$199.99
HPE ProLiant MicroServer Gen10 Plus v2 Ultra Micro Tower Server - 1 x Intel Xeon
$846.19
HP ProLiant Xeon E3-1220L V2 2.30 GHz 16 GB RAM MicroServer Gen8 NO DRIVES
$199.99
HP ProLiant HSTNS-5151 Micro Server 8GB RAM No Drives/Key/Caddies *READ*
$94.99
SuperMicro Server 505-2 Intel Atom 2.4GHz 8GB RAM SYS-5018A-FTN4 1U Rackmount
$202.49
Supermicro 5018A-FTN4 Rack Server - Black
$125.00
SuperMicro SuperServer 505-2 Intel Atom @ 2.4GHz 8GB w/ Ears 5018A-FTN4
$159.80
SUPERMICRO CSE-512 AMD Opteron Processor 6128, 32GB DDR3 RAM NO HDD
$90.00
2U 12 Bay SAS3 SuperMicro Server 6028U-TR4T+ W/ X10DRU-i+ Barebone 12 Caddy RAIL
$299.00