-
File copy gives error message "Success"
Hi all, Recently a motherboard in an old pc of mine toasted itself... It contained some important data, so I pulled out the HDD and put it in my good pc and booted Knoppix (the old one was running Debian, so I couldn't pull out the data with Windows *sigh*). However, when I try to copy my data to an USB HDD, I randomly keep getting the error message "Success" and then PCMan stops copying the files... It doesn't show up with every file and it doesn't even occur for the same file everytime. Quite a strange error message and I can't find any info related to it. This is no issue of having not enough space on my external HDD, because I have 971,9 GB left. That should be enough for 18GB of data, right? Could it have something to do with the fact that the HDD is (probably) NTFS formatted? Knoppix seems to be using FUSE for this, and I am totally unfamiliar with that system... Here is the line mount gives me for the external HDD:
Code:
/dev/sdf1 on /media/sdf1 type fuseblk (rw,nosuid,nodev,relatime,user_id=1000,group_id=1000,allow_other,blksize=4096)
Thanks in advance, Eric Spreen
-
Originally Posted by
erispre
Hi all, Recently a motherboard in an old pc of mine toasted itself... It contained some important data, so I pulled out the HDD and put it in my good pc and booted Knoppix (the old one was running Debian, so I couldn't pull out the data with Windows *sigh*). However, when I try to copy my data to an USB HDD, I randomly keep getting the error message "Success" and then PCMan stops copying the files... It doesn't show up with every file and it doesn't even occur for the same file everytime. Quite a strange error message and I can't find any info related to it. This is no issue of having not enough space on my external HDD, because I have 971,9 GB left. That should be enough for 18GB of data, right? Could it have something to do with the fact that the HDD is (probably) NTFS formatted? Knoppix seems to be using FUSE for this, and I am totally unfamiliar with that system... Here is the line mount gives me for the external HDD:
Code:
/dev/sdf1 on /media/sdf1 type fuseblk (rw,nosuid,nodev,relatime,user_id=1000,group_id=1000,allow_other,blksize=4096)
Thanks in advance, Eric Spreen
Two possibilities: 1) There's a problem with the old drive and/or filesystem; have you tried looking at it with GParted? It might tell you something useful. If it's NTFS, you can download a disk called "Hiten's BootCD", which will at least allow you to do a DOS chkdsk command.
2) There's something goofy with Pcman, and it can be done with a cp command in lxterm. You can Google for more on copying at the command line.
Hope that helps!
Krishna
-
Senior Member
registered user
@erispre
If you like to find out more about the filesystem's type on your USB HDD then you can use the blkid command.
Code:
sudo blkid /dev/sdf1
Do you use Knoppix 6.2.1? You could try GNU Midnight Commander mc instead of PCMan Filemanager.
Tags for this Thread
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Extron RGB-160XI Analog Computer Video 60-378-01
$187.06
The analog thing modern open source, educational, low-cost analog computer
$800.00
NEW Aquarius+ Computer Signature Edition - 8Bit Retro System
$229.00
Apple Macintosh SE/30 M5119 Computer 8MB RAM Recapped Working *See Description*
$475.00
IBM Modem Saver Phone Line Tester
$7.99
Landen Computer. Circa 1898. the Rapid Computer Company. With Original Case.
$425.00
NEW Aquarius+ Mini 8Bit Retro Computer System - Assembled PCB ONLY
$99.00
Soviet Union motherboard analog computer ZX Spectrum USSR
$97.00
ACASIS PCIE Capture Card HDMI 1.4 1080P60HZ PCIE 2.0 X4 20Gbps for Video Capture
$248.99
Sunrise Telecom CM750 Analog & Digital SLM Network Analyzer
$39.99