-
Noob question about making a knoppix cd
Hi i've been trying to make a knoppix cd but when i use the cd it says there is no bootable program. I used roxio easy cd dvd creator. So i tried to download another version of knoppix but that didn't work too. Is it possible that the cd doesnt work because i only put the iso file unto the cd and not that other files(there were 4 little files which are a few kb big). So i tried to ut them unto the cd also but i can only put one file onto the cd!
any suggestions????
-
Senior Member
registered user
If your problem is what to do with an iso, see if this helps:
http://www.psychocats.net/ubuntu/iso
Ignore the cat.
-
Senior Member
registered user
@tok121
Did you read the Downloading FAQ in the wiki? There is a section
Q: I have downloaded the ISO file. How do I burn the ISO? How is the ISO supposed to be burned? http://www.knoppix.net/wiki/Download...o_be_burned.3F
I use ImgBurn http://www.imgburn.com/ to burn ISO image files.
-
Senior Member
registered user
@klaus2008
Hi, klaus.
Since I've already admitted to not being an expert, I can also admit that
I could not readily find an answer using any of the forum's search boxes.
I'm not sure I even found any relevant FAQ or Wiki on this.
Are you sure it's still here?
-
Senior Member
registered user
This was really hard to find:
http://www.knoppix.net/wiki/Download...o_be_burned.3F
If we didn't have the link.
Last edited by utu; 08-05-2010 at 06:13 PM.
-
Senior Member
registered user
Outside the forum, with the search key in Google
knoppix burning iso
Your entry shows up as #1.
The forum itself gives this up rather grudgingly.
-
Administrator
Site Admin-
Originally Posted by
utu
The forum itself gives this up rather grudgingly.
That is because the forum isn't the right place to look for documentation. The forum is for discussion. The wiki is for documentation. And it is reached by the "Documentation" link on the top of every forum page. (Imagine that!) Once a user gets to the wiki, the proper section to read is the "Downloading FAQ" which gives all of the information needed to properly download and verify the download and then burn to CD properly. We have seen all of the typical errors over and over again. They could all be found by extensive searching of the forums, but that would be pointless, they are all neatly organized in one place in the FAQ.
---
Verifying of md5 checksum and burning a CD at slow speed are important.
-
Senior Member
registered user
Hi, utu
You don't have to do a search from outside because the website KNOPPIX.net has got a search page http://www.knoppix.net/s.html
-
Senior Member
registered user
-
Administrator
Site Admin-
Originally Posted by
tok121
Hi i've been trying to make a knoppix cd but when i use the cd it says there is no bootable program.....
So have you managed to read the Downloading FAQ and make a bootable CD yet? It can be confusing until you read the instructions but the details are well documented.
---
Verifying of md5 checksum and burning a CD at slow speed are important.
Tags for this Thread
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Cisco SG95-16 16-Port Gigabit Switch SG95-16-KR
$47.00
Cisco RV320 Dual WAN VPN 4 Port Gigabit Router w/ Web Filtering RV320-WB-K9-NA
$374.00
Cisco IP Phone 6841 – CP-6841-3PW-NA-K9=
$75.00
Cisco SG110 24 Port Gigabit Ethernet Switch w/ 2 x SFP SG110-24
$117.00
Cisco WS-C3850-48P-L 48-Port Gigabit 3850 PoE Switch w/ 715W+ C3850-NM-4-1G Mod
$83.00
Cisco QSFP-40G-SR-BD BiDi Short-reach Transceiver, 1 Year Warranty
$17.25
Cisco C3850-NM-2-10G 2 Port Network Exp.Module for 3850
$38.99
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
Cisco WS-C3850-48F-S Catalyst 3850 48x 1GB PoE+ RJ-45 1x Module Switch
$185.00
Cisco WS-C3850-48P-L 48-Port Gigabit 3850 PoE Switch w/ 715W Network Switch
$41.43