If your problem is what to do with an iso, see if this helps:
http://www.psychocats.net/ubuntu/iso
Ignore the cat.
Hi i've been trying to make a knoppix cd but when i use the cd it says there is no bootable program. I used roxio easy cd dvd creator. So i tried to download another version of knoppix but that didn't work too. Is it possible that the cd doesnt work because i only put the iso file unto the cd and not that other files(there were 4 little files which are a few kb big). So i tried to ut them unto the cd also but i can only put one file onto the cd!
any suggestions????
If your problem is what to do with an iso, see if this helps:
http://www.psychocats.net/ubuntu/iso
Ignore the cat.
@tok121
Did you read the Downloading FAQ in the wiki? There is a section
Q: I have downloaded the ISO file. How do I burn the ISO? How is the ISO supposed to be burned? http://www.knoppix.net/wiki/Download...o_be_burned.3F
I use ImgBurn http://www.imgburn.com/ to burn ISO image files.
@klaus2008
Hi, klaus.
Since I've already admitted to not being an expert, I can also admit that
I could not readily find an answer using any of the forum's search boxes.
I'm not sure I even found any relevant FAQ or Wiki on this.
Are you sure it's still here?
This was really hard to find:
http://www.knoppix.net/wiki/Download...o_be_burned.3F
If we didn't have the link.
Last edited by utu; 08-05-2010 at 06:13 PM.
Outside the forum, with the search key in Google
knoppix burning iso
Your entry shows up as #1.
The forum itself gives this up rather grudgingly.
Hi, utu
You don't have to do a search from outside because the website KNOPPIX.net has got a search page http://www.knoppix.net/s.html
That is because the forum isn't the right place to look for documentation. The forum is for discussion. The wiki is for documentation. And it is reached by the "Documentation" link on the top of every forum page. (Imagine that!) Once a user gets to the wiki, the proper section to read is the "Downloading FAQ" which gives all of the information needed to properly download and verify the download and then burn to CD properly. We have seen all of the typical errors over and over again. They could all be found by extensive searching of the forums, but that would be pointless, they are all neatly organized in one place in the FAQ.
---
Verifying of md5 checksum and burning a CD at slow speed are important.
Exactly my point.
57-1000333-01 Brocade XBR-000212 32G Multi-mode SFP
$29.00
Cisco SG110 24 Port Gigabit Ethernet Switch w/ 2 x SFP SG110-24
$117.00
Mellanox 10/25GbE SFP28 Network Card MCX512A-ACAT ConnectX-5 EN Ethernet Adapter
$284.00
INTEL 10G SFP+ SR SFP E10GSFPSR FTLX8571D3BCV-IT For X520-DA2 X520-SR2 X710-DA2
$15.90
NEW Sealed Cisco SFP-10G-LR 10GBASE-LR SFP+ 1310nm 10km *US Shipping*
$18.00
F5 Networks 10GB OPT-0016-00 F5-UPG-SFP+-R 10GBASE/SR SFP Transceiver
$4.00
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
Mellanox Original MFM1T02A-SR 10GbE 10GBASE-SR SFP+ Transceiver
$9.00
10 PCS Cisco GLC-LH-SMD 10-2625-01 1310nm SFP Transceiver Module
$85.00
Cisco 10G SFP+ Module SFP-10G-SR 10-2415-03 (Lot of 5)
$24.99